Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

VPN tunnel problems between rv120w and wrvs4400

Good morning,

any ideas ?

I am trying to make a vpn tunnel from one location to another ...

situation a : cisco wrvs4400 router

situation b : rv120w router ...

all is setup but this is my log error

[rv120w][IKE] ERROR:  Ignore information because the message has no hash payload.

2013-10-05 05:54:13: [rv120w][IKE] INFO:  Using IPsec SA configuration: 10.0.0.0/24<->192.168.0.0/24

2013-10-05 05:54:13: [rv120w][IKE] INFO:  Configuration found for ..............

2013-10-05 05:54:13: [rv120w][IKE] INFO:  Initiating new phase 1 negotiation: 85.234.195.185[500]<=>81.82.192.144[500]

2013-10-05 05:54:13: [rv120w][IKE] INFO:  Beginning Identity Protection mode.

2013-10-05 05:54:13: [rv120w][IKE] INFO:   [ident_i1send:180]: XXX: NUMNATTVENDORIDS: 3

2013-10-05 05:54:13: [rv120w][IKE] INFO:   [ident_i1send:184]: XXX: setting vendorid: 4

2013-10-05 05:54:13: [rv120w][IKE] INFO:   [ident_i1send:184]: XXX: setting vendorid: 8

2013-10-05 05:54:13: [rv120w][IKE] INFO:   [ident_i1send:184]: XXX: setting vendorid: 9

2013-10-05 05:54:13: [rv120w][IKE] ERROR:  Ignore information because the message has no hash payload.

2013-10-05 05:54:23: [rv120w][IKE] ERROR:  Ignore information because the message has no hash payload. 2013-10-05 05:54:13: [rv120w][IKE] INFO:  Using IPsec SA configuration: 10.0.0.0/24<->192.168.0.0/24
2013-10-05 05:54:13: [rv120w][IKE] INFO:  Configuration found for ....................
2013-10-05 05:54:13: [rv120w][IKE] INFO:  Initiating new phase 1 negotiation: .........................[500]<=>......................[500]
2013-10-05 05:54:13: [rv120w][IKE] INFO:  Beginning Identity Protection mode.
2013-10-05 05:54:13: [rv120w][IKE] INFO:   [ident_i1send:180]: XXX: NUMNATTVENDORIDS: 3
2013-10-05 05:54:13: [rv120w][IKE] INFO:   [ident_i1send:184]: XXX: setting vendorid: 4
2013-10-05 05:54:13: [rv120w][IKE] INFO:   [ident_i1send:184]: XXX: setting vendorid: 8
2013-10-05 05:54:13: [rv120w][IKE] INFO:   [ident_i1send:184]: XXX: setting vendorid: 9
2013-10-05 05:54:13: [rv120w][IKE] ERROR:  Ignore information because the message has no hash payload.
2013-10-05 05:54:23: [rv120w][IKE] ERROR:  Ignore information because the message has no hash payload.

any ideas ?

1 REPLY
New Member

VPN tunnel problems between rv120w and wrvs4400

After some wigeling and changing all is working

This problem is solved, it was a wrong pasword encryption setting between routers

334
Views
0
Helpful
1
Replies
CreatePlease to create content