Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Can anyone help me to make a walkthrough for SG300 and VLANs

Can anyone help me to make a walkthrough for programming of this setup ..

I have tried most of the options, and i cant get the VLANs on the internet.

I do use RV-042G, SG-300, SG-200 and WAP321..

im stuck so i hope someone can help or i have alot of Cisco products for sale

Can it be done

Joar

11 REPLIES
Green

Can anyone help me to make a walkthrough for SG300 and VLANs

Hi Joar, I've explained this on your other topic.

-Tom
Please mark answered for helpful posts

-Tom Please mark answered for helpful posts http://blogs.cisco.com/smallbusiness/
New Member

Can anyone help me to make a walkthrough for SG300 and VLANs

Hi

Yes it did work when i make a statisk DNS adress like 8.8.8.8 on each pc... but i cant find any place to put the DNS info on the switch... for all vlans.. så i are close to give it up now, thets why i start a new topic so maybe i cant start and get it right from the first settings.. i did also make the network drawing easy to see how i trye to setting it up.. i did think the first drowing was not easy to read..

Thx and sorry for start it up agen..

Joar

Gold

Can anyone help me to make a walkthrough for SG300 and VLANs

Joar,

Thank you for the explanation, I understand. Under the settings to Add Network Pool there is a setting for Domain Name Server IP Address (Option 6). Change that to Other and use the RV042G address or 8.8.8.8.

- Marty

Gold

Can anyone help me to make a walkthrough for SG300 and VLANs

Joar,

Tom provided excellent instruction to configure the devices in your previous thread. You wrote "Thx, now it work on wire.."

Can you be more specific about what is and what is not working? If you did what Tom recommended it should be working perfectly.

- Marty

New Member

Can anyone help me to make a walkthrough for SG300 and VLANs

Hi

I did write a replay for Tom now, and trye to be spesific.. it hve to be somthing i did not get in this..

One thing, do i have to disable DHCP server on the RV042 and act. it on SG300 ? or can i use the DHCP server on RV042g for vlan 1 and DHCP server for vlan 2-3 on SG300 ...?

i use gateway like this : ip: 192.168.2.2 mask:255.255.255.0 gw:192.168.2.1

i did also try gw 192.168.1.1 (ip for RV042g)

Joar

Gold

Re: Can anyone help me to make a walkthrough for SG300 and VLANs

Joar,

DHCP will not pass between the router and the switch on VLAN 1. You should configure the switch with all 3 DHCP scopes.

IP settings are fine.

- Marty

Gold

Re: Can anyone help me to make a walkthrough for SG300 and VLANs

Joar,

Please note that I edited my above answer. I realized that the switch is in router mode.

- Marty

New Member

Can anyone help me to make a walkthrough for SG300 and VLANs

Hi Marty

Yea, i try to disable DHCP in RV-042G and put up a ip-pool in SG-300 then.. but i cant ping the RV-042G from any vlan.. i can ping 192.168.2.1 and 192.3.1 but i cant ping 192.168.1.1 or 8.8.8.8.. do i need to open something in the firewall ?

Joar

Green

Can anyone help me to make a walkthrough for SG300 and VLANs

Joar, try to use this for help

https://supportforums.cisco.com/thread/2123434

-Tom Please mark answered for helpful posts http://blogs.cisco.com/smallbusiness/
New Member

Re: Can anyone help me to make a walkthrough for SG300 and VLANs

Hi

I post my settings from RV-042G.. i can ping 8.8.8.8 from vlan 1, but not from vlan 2-3

vlan 1 :

vlan1.jpg

and vlan 3:

vlan3.jpg

and my Static Routing on RV-024G is :

Destination IP

Subnet Mask

Default Gateway

Hop Count

Interface
80.203.xxx.1255.255.255.255*0ppp1
192.168.3.0255.255.255.0*0eth0
192.168.3.0255.255.255.0192.168.3.11eth0
192.168.2.0255.255.255.0*0eth0
192.168.2.0255.255.255.0192.168.2.11eth0
192.168.1.0255.255.255.0*0eth0
192.168.10.0255.255.255.0*0eth0
192.168.10.0255.255.255.0192.168.10.11eth0
default0.0.0.080.203.xxx.140ppp1

do you see any wrong ?

Thx

Green

Re: Can anyone help me to make a walkthrough for SG300 and VLANs

I cannot make it any more clear than your first post and the pictures on that link...

If you cannot make the configuration work, please call the small business support center.

-Tom
Please mark answered for helpful posts

-Tom Please mark answered for helpful posts http://blogs.cisco.com/smallbusiness/
359
Views
0
Helpful
11
Replies
CreatePlease to create content