Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

How to change IP address on Layer 3 Mode on a SG300-28?

Hi all,

I just bought a SG300-28, it is upgrade to the latest version firmware.

And then I am change it work on L3 Mode (Yes, I need it much work on L3 Mode)

Ok, but when I go to IP Configuration Page on the VLAN 1 (Please see the image)

http://explorerhome.dyndns.org/q/SG300-28_001.jpg

Edit it to static can't let me change it IP (Yes, it is now working on DHCP mode, and get a IP from my Firewall auto, it is IP 192.168.218.37 there)

How do I force the VLAN1 or Port 1 is IP 192.168.218.3 by GUI or by other way?

Best Regards,

Jimmy Chan

http://explorerhome.dyndns.org/blog

2 ACCEPTED SOLUTIONS

Accepted Solutions
Green

How to change IP address on Layer 3 Mode on a SG300-28?

Hi Jimmy, the easiest and fastest way to do this is in the CLI.

If you don't have a console, you can use telnet. To enable the telnet go to Security 0> TCP/UDP services, check the box for telnet and apply this.

Once done, telnet to the switch and log in

use the commands

config t

interface vlan 1

ip address x.x.x.x x.x.x.x  (x.x.x.x = ip addresss and the second x.x.x.x = the mask something like 192.168.218.3 255.255.255.0)

-Tom
Please mark answered for helpful posts

-Tom Please mark answered for helpful posts http://blogs.cisco.com/smallbusiness/
Green

How to change IP address on Layer 3 Mode on a SG300-28?

hi jimmy,

you can use the command

wr mem

or

copy run start

-Tom
Please mark answered for helpful posts

-Tom Please mark answered for helpful posts http://blogs.cisco.com/smallbusiness/
5 REPLIES
Green

How to change IP address on Layer 3 Mode on a SG300-28?

Hi Jimmy, the easiest and fastest way to do this is in the CLI.

If you don't have a console, you can use telnet. To enable the telnet go to Security 0> TCP/UDP services, check the box for telnet and apply this.

Once done, telnet to the switch and log in

use the commands

config t

interface vlan 1

ip address x.x.x.x x.x.x.x  (x.x.x.x = ip addresss and the second x.x.x.x = the mask something like 192.168.218.3 255.255.255.0)

-Tom
Please mark answered for helpful posts

-Tom Please mark answered for helpful posts http://blogs.cisco.com/smallbusiness/
New Member

How to change IP address on Layer 3 Mode on a SG300-28?

Tom,

Thank you very much.

But, one more question ...

How to CLI save the running-config to the flash, so on future reboot will not lose anything on it?

Best Regards,

Jimmy Chan

http://explorerhome.dyndns.org/blog

Green

How to change IP address on Layer 3 Mode on a SG300-28?

hi jimmy,

you can use the command

wr mem

or

copy run start

-Tom
Please mark answered for helpful posts

-Tom Please mark answered for helpful posts http://blogs.cisco.com/smallbusiness/
New Member

Re: How to change IP address on Layer 3 Mode on a SG300-28?

Hi,

For Web GUI based setup I think this article's Change the IP Address of the Switch section would be helpful


Initial Configuration on 200/300 Series Managed Switches

New Member

Re: How to change IP address on Layer 3 Mode on a SG300-28?

Vishal,

Thank you of the KB link, but I am using Layer 3 Mode, so my case look like not work on above link since it is for Layer 2.

Whatever it is L3 or L2 Mode, I am still very thank you of your kindly help for a newbie like me there.

Thank you.

Best Regards,

Jimmy Chan

http://explorerhome.dyndns.org/blog

2679
Views
5
Helpful
5
Replies
CreatePlease login to create content