Hi There, I have a SG300-10MP, running in L3 Mode. connected to a ddwrt modem/router (to be replaced in the near future) 192.168.32.1 latest firmware, & 3x Networks I am having issues routing between the VLANs and connecting to the Internet (or even the Router) I am using both CLI and GUI and have been trying for a couple of days and feel as though I am constantly missing something simple. What I want is to be able to access the Web from either VLAN and to be able to connect between the VLANs if required. I want to have as much of the setup on the SG300, so I can change the modem out with other models quickly. I am running the SG300 as a DHCP server, VLAN 20 is for PRI users (ports 1-4) VLAN 30 is for SEC users (ports 5-8) VLAN 40 is for the connection to the router. (port 10) I can ping hosts on all 3 networks directly from the SG300, and I can Ping the SG300 interface address from other devices, (even across VLAN) but no device to device) (no firewalls etc as proven by the router to device ping) I have tried ARP proxy ON and OFF with no change
any suggestions are appreciated.
Thank you in advance,
TESTSWITCH#show run config-file-header TESTSWITCH v18.104.22.168 / R750_NIK_1_35_647_358 CLI v1.0 set system mode router
file SSD indicator encrypted @ ssd-control-start ssd config ssd file passphrase control unrestricted no ssd file integrity control ssd-control-end cb0a3fdb1f3a1af4e4430033719968c0 ! vlan database vlan 20,30,40 exit voice vlan oui-table add 0001e3 Siemens_AG_phone________ voice vlan oui-table add 00036b Cisco_phone_____________ voice vlan oui-table add 00096e Avaya___________________ voice vlan oui-table add 000fe2 H3C_Aolynk______________ voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone voice vlan oui-table add 00d01e Pingtel_phone___________ voice vlan oui-table add 00e075 Polycom/Veritel_phone___ voice vlan oui-table add 00e0bb 3Com_phone______________ ip dhcp server ip dhcp pool network PRI address low 192.168.20.2 high 192.168.20.249 255.255.255.0 lease 5 domain-name PRI dns-server 22.214.171.124 exit ip dhcp pool network SEC address low 192.168.30.2 high 192.168.30.249 255.255.255.0 dns-server 126.96.36.199 exit bonjour interface range vlan 1 hostname TESTSWITCH snmp-server location KEL snmp-server contact NIC ! interface vlan 1 no ip address dhcp ! interface vlan 20 name PRI ip address 192.168.20.250 255.255.255.0 ! interface vlan 30 name SEC ip address 192.168.30.1 255.255.255.0 ! interface vlan 40 name TRUNK ip address 192.168.32.250 255.255.255.0 ! interface gigabitethernet1 switchport mode access switchport access vlan 20 ! interface gigabitethernet2 switchport mode access switchport access vlan 20 ! interface gigabitethernet3 switchport mode access switchport access vlan 20 ! interface gigabitethernet4 switchport mode access switchport access vlan 20 ! interface gigabitethernet5 switchport mode access switchport access vlan 30 ! interface gigabitethernet6 switchport mode access switchport access vlan 30 ! interface gigabitethernet7 switchport mode access switchport access vlan 30 ! interface gigabitethernet8 switchport mode access switchport access vlan 30 ! interface gigabitethernet9 ip address 192.168.2.250 255.255.255.0 ! interface gigabitethernet10 switchport trunk native vlan 40 ! exit banner login ^C TEST ^C banner exec ^C BE CAREFUL ^C ip default-gateway 192.168.32.1
Hi Tom, Thanks for the reply, I looked through the link provided and checked it against the config I used, The RV--- Router looks like a good option for further down the track, but with the ddwrt at the moment I dont have the ability to allow multiple subnets, I have static routes on there already. Still no success.
Introduction:Topology Diagram:Configuration Overview:Related
Information: Introduction: This document describes how to connect SG300
with Catalyst switch via STP. Spanning Tree Protocol (STP) is a Layer 2
protocol that runs on mainly on switches. The spec...
The Sx500 Series Stackable Switches offers different port features. You
can add security to a port, make the port more energy efficient, map a
VLAN to a port, make a port available or not to a specific network
portion, and so forth. The next set of articl...
Recently, HP Networking published a blog post attempting to counter the
favorable third party Miercom report on our Cisco® 200 and 300 Series
Smart and Managed switches: