Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Virtual Assistant- Discover support content and options for your gearSupport page index - Contains a ...
Forum Posts
I have questions in cluster settings. (1) Number of WAP devices per single point setting WAP150:4 Does the setting 'WAP150:4' indicate that a maximum of 4 WAP devices can be connected in a single cluster? (2) Registering an AP in a Created Clu...
Hi, I have Mikrotik Cloud base router its connect with cbs 100 switch (WAN) and its connect with cbs350(LAN). I am getting this error. Kindly this one is from swx side or WAN side and what's the solution. Thanks @
Hi,I have tried to retrieve serial number info for 3 units of the Cisco WAP4410N Access Point devices via Web GUI and CLI, but it seems can't find the serial number info for this model. Kindly advise further, thanks.Regards,Wilson Leong
Resolved! configuration cisco 140 AC access point
Hello Team.I have a problem with the Cisco 140 AC access points that I am installing at a client's home. We have followed the configuration procedures:- we created an administrator account-I created a wireless network- I confirmed the settings- when ...
First off, I have to say I am EXTREMELY dissatisfied with Cisco's supposed support. I just bought this device and it is not connecting. I did the usual google searches and nothing helps. I watched the Tech Talk videos and followed the directions w...
Resolved! Multiple CBW Masters
Hi,Is it possible to have multiple CBW Masters on the same network? It appears that the MAC address used is static and hence two is an issue?Many thanksTom.
Hi, I have almost 180 CBW 240AC AP, How to configure and mamage them without controller. What is the maximum number of AP subordinate with Primary AP. Thanks
We had some time ago problems after the firmware update to 1.0.4.3. Frequently several time a week some of the 22 WAP125 access points either had poor network throughput, or were not reachable by wifi or lan (but the SSID was still shown). A hard reb...
Hello all, the dental office has the router RV042G. It does not have the wireless feature. I would like to set up wireless for this office. However, I am not sure which device is good for this environment. I had picked the WAP371 but it did not work....
担当者さま お世話になります。参考資料として、購入予定のCBS350-24T-4G-JPの外観図（3面図）を頂けないでしょうか？（PDF、またはCAD図）よろしくお願いいたします。
Hi,Recently I had to reset all my AP's to factory default, cos I forgot the password. Since then, I can't get my APs working.They stuck in Cycling Colors (Red/Amber/Green). Ok I thought, that I did smth wrong during reset and I went to garage to grab...
Hi there, Hoping someone might have an insight, I seem to be unable to get APs in our Single Point Setup cluster to use channels other than 6/36 and not sure what to try next. If Single Point Setup 'Channel Management' is enabled this screen shows t...
Hi,In our office we have 2 WAP4410N for our clients and guests to have free wifi.Every day or two it seems that noone can connect to the WAPs and they have to be unplugged and plugged back in to start working again. Ive read alot of other people havi...
Hi there,I bought a new CBW150AX and I tried to configure it.However, as the above title, during go live on CBW150AX, I can see "Device connected" but sometime later "Failed to connect".In addition, I cannot connect the start page "ciscobusiness.cisc...
Resolved! % Invalid input detected at '^' marker.
Hi there,Trying to access to the config terminal, I get error % Invalid input detected at '^' marker. Here is my process :Login to my access point via ssh login as :adminUsing keyboard-interactive authentication.Password:xxxxxxxxxxxAP>enablePassword...
