Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Error message after upgrade

I got the following message when trying to telnet to our switch after upgrading from 3.3(4a) to 3.3(5b) on our MDS 9120 (after supplying my credentials):

telnet login is temporarily not available as startup configuration is being applied.

This was after the switch reloaded after issuing the install all command. Since I couldn't telnet I logged in via the console and noticed there was no startup config but the running config was there and correct. After about 30 minutes with the switch being up everything was back to normal. The startup config was there and I all services were up and running.

Has anyone experienced something like this before with an upgrade? During all my past upgrades after the reload (single supervisor switches) the switch was up and running just fine. Something a new to this upgrade for me is that this switch doesn't have an active mgmt interface, we reach this switch using IPFC (create ip interfaces on vsans that are merged between switches).

Everyone's tags (2)
3 REPLIES
Cisco Employee

Error message after upgrade

I suspect you might have enabled debug logging which caused excessive writes on the flash due to that the switch which might have taken some more time for normal operation.

New Member

Error message after upgrade

Everything is currently set to the defualt levels.

show logging level

Facility        Default Severity        Current Session Severity

--------        ----------------        ------------------------

aaa                     2                       2

acl                     2                       2

auth                    0                       0

authpriv                3                       3

bootvar                 5                       5

callhome                2                       2

capability              2                       2

cdp                     2                       2

cert_enroll             2                       2

cfs                     3                       3

confcheck               2                       2

cron                    3                       3

daemon                  3                       3

device-alias            3                       3

dstats                  2                       2

ethport                 5                       5

fc-redirect             5                       5

fc-tunnel               5                       5

fc2d                    2                       2

fcc                     2                       2

fcdomain                3                       3

fcns                    2                       2

fcs                     2                       2

fdmi                    2                       2

feature-mgr             2                       2

flogi                   2                       2

fspf                    3                       3

ftp                     3                       3

ipacl                   2                       2

ipconf                  5                       5

ipfc                    2                       2

kern                    6                       6

licmgr                  6                       6

local0                  3                       3

local1                  3                       3

local2                  3                       3

local3                  3                       3

local4                  3                       3

local5                  3                       3

local6                  3                       3

local7                  3                       3

lpr                     3                       3

mail                    3                       3

mcast                   2                       2

module                  5                       5

news                    3                       3

ntp                     2                       2

pfma                    5                       5

platform                5                       5

port                    5                       5

port-resources          5                       5

port_channel            5                       5

prefpath                2                       2

qos                     3                       3

radius                  2                       2

rdl                     2                       2

rib                     2                       2

rlir                    2                       2

rscn                    2                       2

scheduler               5                       5

scsi-target             2                       2

securityd               2                       2

span                    5                       5

syslog                  3                       3

sysmgr                  3                       3

System Health LC        4                       4

SystemHealth            4                       4

tlport                  4                       4

user                    3                       3

uucp                    3                       3

vni                     2                       2

vrrp_cfg                5                       5

vrrp_eng                5                       5

vsan                    2                       2

vshd                    5                       5

wwn                     3                       3

xbar                    5                       5

zone                    2                       2

0(emergencies)          1(alerts)       2(critical)

3(errors)               4(warnings)     5(notifications)

6(information)          7(debugging)

New Member

Error message after upgrade

Does that behavior occurs with all the users? admin as well?

601
Views
0
Helpful
3
Replies
CreatePlease login to create content