Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

half duplex or full duplex configuration for MDS9124 management port?

Hi All,

Is it possible to set the management port of mds 9124 about half or full duplex configuration?

I want to correct following error:

Jun 13 10:27:20.799 GMT: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on GigabitEthernet4/18 (not half duplex), with mtw1pc02bs0(FOX1450G8QG) mgmt0 (half duplex).

it seems mds 9124 set his port to half duplex.

Dennis

Everyone's tags (1)
2 ACCEPTED SOLUTIONS

Accepted Solutions
New Member

half duplex or full duplex configuration for MDS9124 management

You may want to check this thread :

https://supportforums.cisco.com/thread/2059109

Else try the following :

switch# config terminal

switch(config)#

switch(config)# interface mgmt0

switch(config-if)# switchport duplex full

switch(config)# exit

switch#

switch# copy running-config startup-config

Also, I would suggest you check what the counterpart of your MDS switch mgmt interface is set to (i.e. is it set to autoneg, then try setting it to fix speed/duplex or the other way around).

Cisco Employee

half duplex or full duplex configuration for MDS9124 management

Hi Dennis,

You might have hit bug CSCte76880 (http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCte76880)

Configure both interfaces to auto duplex achieve a full duplex connection as a workaround, or upgrade to 4.2(7e) or 5.0(4d) where the fix has been integrated.

Best Regards,

Vincent

4 REPLIES
New Member

half duplex or full duplex configuration for MDS9124 management

You may want to check this thread :

https://supportforums.cisco.com/thread/2059109

Else try the following :

switch# config terminal

switch(config)#

switch(config)# interface mgmt0

switch(config-if)# switchport duplex full

switch(config)# exit

switch#

switch# copy running-config startup-config

Also, I would suggest you check what the counterpart of your MDS switch mgmt interface is set to (i.e. is it set to autoneg, then try setting it to fix speed/duplex or the other way around).

Cisco Employee

half duplex or full duplex configuration for MDS9124 management

Hi Dennis,

You might have hit bug CSCte76880 (http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCte76880)

Configure both interfaces to auto duplex achieve a full duplex connection as a workaround, or upgrade to 4.2(7e) or 5.0(4d) where the fix has been integrated.

Best Regards,

Vincent

Cisco Employee

half duplex or full duplex configuration for MDS9124 management

Hi Dennis,

is there a reason you're not using auto detect?

New Member

half duplex or full duplex configuration for MDS9124 management

Hi Kris,

Becasue network admin told me that he got the error message:

Jun 13 10:27:20.799 GMT: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on GigabitEthernet4/18 (not half duplex), with mtw1pc02bs0(FOX1450G8QG) mgmt0 (half duplex).

Best Regards,

Dennis

3689
Views
0
Helpful
4
Replies