Customer production enviroment is nessus 5000 use 1 G interface * 4 and config Port-channel ( LACP ) uplink to C3560 , The port channel link is 802.1q trunk , but Data trsnsfer is low , the sh interface display as follow :
someone can help me why transfer performance pool and how to fix
N-5548UP# sh int ethernet 1/30 Ethernet1/30 is up Hardware: 1000/10000 Ethernet, address: 547f.ee14.ed25 (bia 547f.ee14.ed25) MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA Port mode is trunk full-duplex, 1000 Mb/s, media type is 10G Beacon is turned off Input flow-control is off, output flow-control is off Rate mode is dedicated Switchport monitor is off EtherType is 0x8100 Last link flapped 9week(s) 6day(s) Last clearing of "show interface" counters 20w2d 30 seconds input rate 152 bits/sec, 19 bytes/sec, 0 packets/sec 30 seconds output rate 1440 bits/sec, 180 bytes/sec, 1 packets/sec Load-Interval #2: 5 minute (300 seconds) input rate 80 bps, 0 pps; output rate 752 bps, 0 pps RX 23530565 unicast packets 1591454 multicast packets 393730 broadcast packets 25515749 input packets 15800394415 bytes 8504065 jumbo packets 0 storm suppression bytes 1491713 runts 0 giants 291 CRC 0 no buffer 1492004 input error 0 short frame 0 overrun 0 underrun 0 ignored 0 watchdog 0 bad etype drop 0 bad proto drop 0 if down drop 0 input with dribble 0 input discard 0 Rx pause TX 459711694 unicast packets 1292248 multicast packets 163261 broadcast packets 461167203 output packets 61814266750 bytes 399778 jumbo packets 0 output errors 0 collision 0 deferred 0 late collision 0 lost carrier 0 no carrier 0 babble 0 Tx pause 1 interface resets
N-5548UP# sh int ethernet 1/30 counters detailed Ethernet1/30 Rx Packets: 25515750 Rx Unicast Packets: 23530565 Rx Multicast Packets: 1591454 Rx Broadcast Packets: 393731 Rx Jumbo Packets: 8504065 Rx Bytes: 15800394483 Rx Packets from 0 to 64 bytes: 1491755 Rx Packets from 65 to 127 bytes: 7903129 Rx Packets from 128 to 255 bytes: 5915278 Rx Packets from 256 to 511 bytes: 1004624 Rx Packets from 512 to 1023 bytes: 290545 Rx Packets from 1024 to 1518 bytes: 406354 Rx Trunk Packets: 23924310 Tx Packets: 461167235 Tx Unicast Packets: 459711724 Tx Multicast Packets: 1292250 Tx Broadcast Packets: 163261 Tx Jumbo Packets: 399778 Tx Bytes: 61814270196 Tx Packets from 0 to 64 bytes: 315 Tx Packets from 65 to 127 bytes: 354626277 Tx Packets from 128 to 255 bytes: 2688006 Tx Packets from 256 to 511 bytes: 100485581 Tx Packets from 512 to 1023 bytes: 1096685 Tx Packets from 1024 to 1518 bytes: 1870593 Tx Trunk Packets: 460868937 Runt Errors: 1491713 Input CRC Errors: 291 Input Errors: 1492004
clearly the input errors/runts on the interface on e1/30 could be playing a part in performance degradation. We need to resolve them first. What do you see for 'show interface' for the port on 3560 going to e1/30 on n5k ? Any output errors? Can you please paste that output as well ? Also how about other interfaces in the same port channel on n5k? Are they showing similar errors or just this one ?
VMware Trunk Port Group is supported from ACI version 2.1
VMM integration must be configured properly
ASA device package must be uploaded to APIC
ASAv version must be compatible with ACI and device package version
In the Previous articles of ACI Automation, we are using Postman/Newman as the Rest API tool to automate the ACI Configuration.
In this article I’m going to discuss on usin...
One of the first steps in building your ACI Fabric is to go through Fabric Discovery. While Fabric Discovery is usually a straightforward process, there are various issues that may prevent you from discovering an ACI switch. This article wil...