Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Nexus 5000 VFC statistics

Hi guys,

I have a working setup but I am wondering why I don't have any statistics available on my VFC interfaces.

lct-n5kup# show int counters fc brief

-------------------------------------------------------------------------------

Interface            Input (rate is 5 min avg)    Output (rate is 5 min avg)

                     ---------------------------  -----------------------------

                     Rate     Total               Rate     Total

                     MB/s     Frames              MB/s     Frames

-------------------------------------------------------------------------------

fc2/1                 406     498410707              0     29318484

fc2/2                 349     464844989              0     27344026

fc2/3                 396     459019674              0     27001360

fc2/4                 387     393548081              0     23150082

fc2/5                 388     415604111              0     24447500

fc2/6                 389     406749980              0     23926672

fc2/7                 389     378549906              0     22267834

fc2/8                 399     409049454              0     24062162

-------------------------------------------------------------------------------

Interface            Input (rate is 5 min avg)    Output (rate is 5 min avg)

                     ---------------------------  -----------------------------

                     Rate     Total               Rate     Total

                     MB/s     Frames              MB/s     Frames

-------------------------------------------------------------------------------

vfc1                    0     0                      0     0

vfc2                    0     0                      0     0

vfc3                    0     0                      0     0

vfc4                    0     0                      0     0

vfc5                    0     0                      0     0

vfc6                    0     0                      0     0

vfc7                    0     0                      0     0

vfc8                    0     0                      0     0

vfc9                    0     0                      0     0

vfc10                   0     0                      0     0

vfc11                   0     0                      0     0

vfc12                   0     0                      0     0

vfc13                   0     0                      0     0

vfc14                   0     0                      0     0

vfc15                   0     0                      0     0

vfc16                   0     0                      0     0

vfc17                   0     0                      0     0

vfc18                   0     0                      0     0

lct-n5kup# show int vfc 1

vfc1 is up

    Bound MAC is 00:00:c9:d0:46:29

    FCF priority is 128

    Hardware is Virtual Fibre Channel

    Port WWN is 20:00:00:0d:ec:e6:31:7f

    Admin port mode is F, trunk mode is on

    snmp link state traps are enabled

    Port mode is F, FCID is 0x010006

    Port vsan is 546

    5 minute input rate 0 bits/sec, 0 bytes/sec, 0 frames/sec

    5 minute output rate 0 bits/sec, 0 bytes/sec, 0 frames/sec

      0 frames input, 0 bytes

        0 discards, 0 errors

      0 frames output, 0 bytes

        0 discards, 0 errors

    Interface last changed at Tue Sep 21 13:47:13 2010

Again everything is working fine but I do not have any statistics on my VFCs.

Any hints on that?

Thanks a lot!

  • Storage Networking
Everyone's tags (3)
2 REPLIES
Cisco Employee

Re: Nexus 5000 VFC statistics

I see you are binding MAC addresses to your vFC rather than interfaces(perhaps you have a downstream FIP snooping switch such as Nexus 4000).

Note that Nexus 5000 does not support interface statistics for MAC bound vFCs.

New Member

Re: Nexus 5000 VFC statistics

Thank you for answering my question.

Could you also give an explanation why the behavior is like that?

782
Views
0
Helpful
2
Replies
This widget could not be displayed.