Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Attention: The Community will be in read-only mode on 12/14/2017 from 12:00 am pacific to 11:30 am.

During this time you will only be able to see content. Other interactions such as posting, replying to questions, or marking content as helpful will be disabled for few hours.

We apologize for the inconvenience while we perform important updates to the Community.

New Member

while configuring speed 1000 i am getting error as sw2-storage-vdc(config-if)# speed 1000 ERROR: Ethernet2/6: Configuration does not match the port capability.

storage-vdc(config-if)# show module

Mod  Ports  Module-Type                         Model              Status

---  -----  ----------------------------------- ------------------ ----------

2    32     1/10 Gbps Ethernet Module           N7K-F132XP-15      ok

sw1-gd78(config-if)# sh module

Mod  Ports  Module-Type                         Model              Status

---  -----  ----------------------------------- ------------------ ----------

2    48     1/2/4/8 Gbps FC Module              DS-X9248-96K9      ok

4    8      10 Gbps FCoE Module                 DS-X9708-K9        ok

7    0      Supervisor/Fabric-2a                DS-X9530-SF2AK9    active *

8    0      Supervisor/Fabric-2a                DS-X9530-SF2AK9    ha-standby

10   22     4x1GE IPS, 18x1/2/4Gbps FC Module   DS-X9304-18K9      ok

Mod  Sw              Hw      World-Wide-Name(s) (WWN)

---  --------------  ------  --------------------------------------------------

2    5.2(2)          1.1     20:41:00:0d:ec:fb:8a:00 to 20:70:00:0d:ec:fb:8a:00

4    5.2(2)          0.107   --

7    5.2(2)          1.8     --

8    5.2(2)          1.8     --

10   5.2(2)          1.3     22:41:00:0d:ec:fb:8a:00 to 22:52:00:0d:ec:fb:8a:00

sw1-gd78(config-if)# sh run int ethernet4/6

!Command: show running-config interface Ethernet4/6

!Time: Mon Feb 20 22:56:12 2012

version 5.2(2)

interface Ethernet4/6

  no shutdown

sw1-gd78(config-if)# no shut

sw1-gd78(config-if)# speed 1000

ERROR: Ethernet4/6: Configuration does not match the port capability.

sw1-gd72# sh int ethernet4/6 capabilities

Ethernet4/6

  Model:                 DS-X9708-K9

  Type (SFP capable):    10Gbase-SR

  Speed:                 1000,10000

  Duplex:                full

  Trunk encap. type:     802.1Q

  Channel:               yes

  Broadcast suppression: percentage(0-100)

  Flowcontrol:           rx-(off/on/desired),tx-(off/on/desired)

  Rate mode:             dedicated

  QOS scheduling:        rx-(2q4t),tx-(1p3q4t)

  CoS rewrite:           yes

  ToS rewrite:           yes

  SPAN:                  yes

  UDLD:                  yes

  Link Debounce:         yes

  Link Debounce Time:    yes

  MDIX:                  no

  Port Group Members:    none

  TDR capable:           no

  FabricPath capable:    yes

  Port mode:             Switched

sw1-gd72# sh int ethernet4/6 transceiver details

Ethernet4/6

    transceiver is present

    type is 10Gbase-SR

    name is CISCO-FINISAR

    part number is FTLX8571D3BCL-CS

    revision is C

    serial number is FNS12090EMJ

    nominal bitrate is 10300 MBit/sec

    Link length supported for 50/125um OM2 fiber is 82 m

    Link length supported for 50/125um OM3 fiber is 300 m

    Link length supported for 62.5/125um fiber is 26 m

    cisco id is --

    cisco extended id number is 4

           SFP Detail Diagnostics Information (internal calibration)

  ----------------------------------------------------------------------------

                                     Alarms                  Warnings

                                High        Low         High          Low

  ----------------------------------------------------------------------------

  Temperature   36.21 C        75.00 C     -5.00 C     70.00 C        0.00 C

  Voltage        3.29 V         3.63 V      2.97 V      3.46 V        3.13 V

  Current        8.11 mA       11.80 mA     4.00 mA    10.80 mA       5.00 mA

  Tx Power       -2.65 dBm       1.49 dBm  -11.30 dBm   -1.50 dBm     -7.30 dBm

  Rx Power       -2.21 dBm       1.99 dBm  -13.97 dBm   -1.00 dBm     -9.91 dBm

  Transmit Fault Count = 0

  ----------------------------------------------------------------------------

  Note: ++  high-alarm; +  high-warning; --  low-alarm; -  low-warning

Everyone's tags (4)
1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

while configuring speed 1000 i am getting error as sw2-storage-v

Ankit,

You are trying to set speed 1000 on a 10g sfp.

type is 10Gbase-SR

You will need to insert a 1gig sfp and then you will be able to set the speed.

Also, I noticed that you posted first with interface 2/6 and the output you gave me was for 4/6. Are you sure you're in the right interface?

4 REPLIES
Cisco Employee

while configuring speed 1000 i am getting error as sw2-storage-v

Can you post a "show mod" and "show int eth 2/6 capa" output? Some of the modules don't support 1gig functionality so your speed 1000 command will fail.

New Member

while configuring speed 1000 i am getting error as sw2-storage-v

Hi Amanda

I have added.

Cisco Employee

while configuring speed 1000 i am getting error as sw2-storage-v

Ankit,

You are trying to set speed 1000 on a 10g sfp.

type is 10Gbase-SR

You will need to insert a 1gig sfp and then you will be able to set the speed.

Also, I noticed that you posted first with interface 2/6 and the output you gave me was for 4/6. Are you sure you're in the right interface?

New Member

while configuring speed 1000 i am getting error as sw2-storage-v

Thanks Amanda....The point You made we have also noticed (type is 10Gbase-SR)...one more question is we cannot configure lesser speed (1G)in our case?

as you talked about interface so these two interface was ISL in my case having same configs.

3307
Views
0
Helpful
4
Replies
CreatePlease to create content