Gents, I need to know if VSS works with mixed supervisor boards (chassi #1 with VS-S720-10G and chassi#2 VS-SUP2T-10G) on 6509-e chassis ? thanks
Gents, I need to know if VSS works with mixed supervisor boards (chassi #1 with VS-S720-10G and chassi#2 VS-SUP2T-10G) on 6509-e chassis ? thanks
Hello,I have a GigE vision camera that implement static LAG (The camera have two 1G NIC's) in order to receive 2G Ethernet.This camera is connected to a computer also with two 1G NIC's that implements static LAG in order to receive more that 1Gbps of...
Hi, Could someone please explain to me why only VLAN 1 in this set up can ping other routers and bits on different subnets and VLAN 2 and 3 can't seem to ping anything? Also DHCP only works for VLAN 1Switch one - hostname SWITCH1!!!!!spanning-tree ...
Good afternoon! We are trying to implement multicasting in our network. Our network is distributed over several square miles, and is serviced by Nexus 5k's at each of our 'core' locations, and a single 7k in our datacenter. We have multicasting wor...
Does anyone know exactly what "My Station TCAM" is?
Greetings, In trying to upgrade IOS on my 2960, I ran into some anomalies and after some research found the following documentation on Cisco's website: From Release Notes for Catalyst 2960 Switches – for IOS Releases 12.2(50)SE and laterHardware Requ...
HiPlease see the attachment for the setup I need advice on. We are designing a new WAN for the company alongside the existing WAN to connect all of our sites. Currently the new WAN is setup and we want to run some test users over it for 2 weeks to en...
Hi,I'm working through a QoS configuration for the 6880-X-LE with 6800Ia FEXs. The QoS configuration, policymap, classes, ACLS etc have all been accepted fine. I can apply a service policy to an interface but when I do I get the following errors come...
HiI have configured mac access list in 4948 switch, but it is not working. Below is the configuration.mac access-list extended testpermit host xxxx.xxxx.xxxx anypermit host xxxx.xxxx.xxxx anyinterface GigabitEthernet1/7mac access-group test inCan any...
Hi everybody.I have 6 Industrial 3010 Switches that are installed on a highway; they're powered by sun cells. When the switches are installed, immediately send this message from the PSOct 8 2015 10:19:16.371: %PLATFORM_ENV-6-FRU_PS_OIR: FRU Power ...
Symtoms -iSCSCi traffic is dropping and Esxi's are getting disconnected frequently ,looked at the interfaces for individual host, I am seeing output errors and TX-pause frames increment BY default flow control is enabled on TX and is disabled on RX ...
i've configured the route-map on a catalyst switch 4503E but when i checked the configuration i can't see the next hop see below the output of show route-map ML-SW-1#show route-map route-map test, permit, sequence 10 Match clauses: interface Fast...
Is it possible to use the same MAC address in multiple VLANs on a Catalyst 2960X-24TS-L?
A customer has recently acquired a cisco 2960 switch which I am to set up.After running the express set up and putting the ip information, the switch was put on the network but the ip address is not pingable and we cannot telnet into it.I also connec...
Hi,I'm just learning how to use EEM on my switch and created an applet that shuts the port down every day after production hours, and brings it back up in the morning. The applet is working well but I want to create a second applet that shuts the por...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-24-2024 02:27 PM | ||
04-23-2024 02:53 AM | ||
04-19-2024 05:58 AM | ||
04-17-2024 03:50 AM | ||
04-15-2024 06:06 PM |
User | Count |
---|---|
11 | |
11 | |
10 | |
9 | |
6 |