Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 

Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

Start a conversation

Resolved! Load balance weight on etherchannels/portchannels

Hello everyone,I know there is a way to set load balance on etherchannels and its based on mac/ip source/dst addresses.But is there a way to set weights for different interfaces? Similar to EIGRP.This is for 3560x and 4500Thank youSent from Cisco Tec...

mario_kmc by • Level 1
  • 2129 Views
  • 5 replies
  • 0 Helpful votes

Resolved! Catalyst 2960 SF Stacking

Hi I am stacking 6 Catalyst 2960 SF Series PoE 48 ports, I am using the Bladestack cable. I plug it in from 1 to 2 on all the switches. If I look at the lights it shows 4 in on group and 2 in another. If I do a show switch detail it shows the followi...

Resolved! Choosing the Next hop IP

Hi Everyone,Say i am  tracing IP 172.30.x.x  from switch Sw1.SW1  shows Sh route showsGateway of last resort is 172.22.101.3 to network 0.0.0.0S     172.16.0.0/12 [1/0] via 172.24.101.1Need to confirm i should choose next hop to destination   via  17...

mahesh18 by • Level 6
  • 446 Views
  • 2 replies
  • 0 Helpful votes

Office Set-up 5505-2960-IPPhone

                   Hey Guys, I had a question about a certain set-up that is coming up. We have a small office going live soon and the set-up is as follows. Our network connection coming in will be linked to a Cisco ASA5505 that will serve as a DHCP ...

Post Error Catalyst 3550

Hey all,I've got a catalyst 3550-48T switch that is having post problems. From power on all ports light up green and status flashes green. After one second the status light changes to solid amber, port 1 is solid amber and the other 47 ports are soli...

SSH connections on LAN servers slow

I have an ASA 5505 in a very simple setup with just 3 vlans - mgmt, internet and LAN. I have some servers in the LAN.Since I have started using ASA 5505 (I had an untangle firewall before), I noticed thart SSH'ing to the servers on the same LAN has a...

Resolved! ASA5505 - Setting up a LAN to access Internet

Hi there,I am new to the Networking and CISCO world, although I used to play around iptables and Untangle firewalls. Unfortunately my laptop does not have a serial port and until I get a USB-to-RS232 adapter I am going to use ASDM for the setup of my...

Cisco 4500 Auto-QOS on Ether-Channel

Hi,Cisco's documentation suggests that auto-qos feature is not supported on ether-channel interfaces. Enabling auto-qos on non-etherchannel interfaces generated all the global qos related configuration and applied service-policy to the interfaces. Ho...

rick505d3 by • Level 1
  • 1814 Views
  • 1 replies
  • 5 Helpful votes

Telnet Issue

I am having cisco 3750 switch, after config line vty (Telnet) in four stack all are working fine only one stack telnet is not working.i am able to ping Mgmt vlan IP. Switch telnet config is ....username cisco privilege 15 password 0 ciscovlan 1521 na...

View All
Review Cisco Networking for a $25 gift card