I am trying the connection above using 10G spf connectors.Is there any special configuration in order to have a trunk (with 2 disctinct vlans) betwen NX7000 and DELL 6224 ?
I am trying the connection above using 10G spf connectors.Is there any special configuration in order to have a trunk (with 2 disctinct vlans) betwen NX7000 and DELL 6224 ?
Hi,I have a vlan that is used for ip cameras. This vlan is routed with other vlans on our Cat 4506-E. how can i implement multicast feature to improve performance?Thanks Sent from Cisco Technical Support iPhone App
HiHaving 2 router with 2 sub interface configured with HSRPThe server seding the data have the route default gw xxx.xxx.xx.252 HSRP adress.but on of the routers did got HW problem so we did shut it down, R2 with IP xxxx.xxxx.xxxx.251, problem so the ...
Hi guys,What is the difference between port priority and system priority in LACp?? are they same??And why exactly it is used?Thanks inadvance
HiJust a quick question, if I configure multiple static RPs and one of the ACLs denies a source will it move on to the next entry that covers it in another acl? e.g.access-list 1 deny 239.0.0.0 0.255.255.255access-list 1 permit 224.0.0.0 15.255.255.2...
Greetings all. Concerning the WS-X4640-CSFP-E module, I was surprised to realize when I got it that the ports are numbered 1-80 rather than 1-40. Then I saw it is actually an 80 port blade when you use half-SFP's. But we have full SFP's, so how does ...
Hi;I am seeing a high " Hulc LED process " that goes up to 21%.Is this a normal percent ?Switch specification:cat 2960-48PST-LIOS 12.2(58)SE1IOS 12.2(58)SE2Thanks
Hi,we have the following setup for our network :UserNetwork - ASA5550 - WAN Router 2911 - ISP Netowrk - Branch Routers 877s / 1941sSince last week we started noticing this problem that the branch users started to complain of slow application response...
I setup corectly a LACP etherchannel with all VLANS allowed. This interface is called Po10. Then I set up another one, Po20, consisting of interfaces 33 and 34, but this time restricting VLANs to only VLAN 20 (all config is below).But when I do a sh ...
I've inherited a system that was set up using vlan1 for management and user data, and I'm trying to reconfigure it to follow best practices with regard to vlans.The main campus is a mix of 3524XL's tied to a 6506 with a SUP1A router engine.The 6506 i...
Hi Team,I am trying to setup WS-SVC-WISM2-K9 on cisco 6509 switch with IOS version 12.2(33)SXJ1.I have completed the below config and seeing service-port up but not coming in oper-up status.I have installed WiSM module in slot 8 and seeing TG8/1, T8/...
Hello, I understand the VCC (vertical cross connect) connects wiring between floors in a building and I know the HCC (horizontal cross connect connects workstations and hosts within each floor, so does that mean the HCC is just a patch panel ?If not,...
We recently installed a WS-X6716-10GE module in slot 6 within a Cisco 6506. We are using two ports on the module (6/13 and 6/14), which are port channeled together to a Nexus 5548. Everything has been running fine for about a month and the card had a...
I'm trying to enable port security on several 4507R's. When I try to configure a range of ports the switch will randomly put 1 or 2 in err-disable. It's different every time I apply the config to the same group of ports. However if I do them one at...
Hello,we have an heterogeneous network with Cisco devices (6509-E, 3750G and 3560) and Alcatel 6850 devices. We have to enable a PTP Wifi line as a backup for the fiber line between two buildings. For this purpose, we have connected a wifi device to ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-24-2024 02:27 PM | ||
04-19-2024 05:58 AM | ||
04-17-2024 03:50 AM | ||
04-15-2024 06:06 PM | ||
04-12-2024 05:48 AM |
User | Count |
---|---|
11 | |
11 | |
10 | |
9 | |
6 |