Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 

Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

Start a conversation

Resolved! Command not available: macro name ....

Hello,I'm trying to setup several macro's but in all Cisco manual's they tell me to use command "macro name ..." to create my macro. But when I want to use the command, my CLI only allows the follwing commands to me: switch(config)#macro ?  auto    M...

Kai Onken by • Level 1
  • 1244 Views
  • 2 replies
  • 0 Helpful votes

Resolved! BPDUs/unmanged switches...

Topic at work if unmanged switches send out BPDUs, I didnt think they did.  I grabbed a el cheapo 5 port unmanged switch, connected up my enet notebook connection to the unmanaged switch, turned on wireshark, and never saw any bpdu's ...was this a co...

route failover

hi! i'm trying to have a backup link thru ASA and a main link thru mpls in our branch office to connect to HQ. The ASA will only take over if the main link failed. there's sla configured at HQ. In this branch office, it's configured with having ospf ...

dave dave by • Level 1
  • 336 Views
  • 1 replies
  • 0 Helpful votes

Layer 2 security

Need to prevent unauthorized users from getting IP address from DHCP when connected to our wired network.In few remote sites we run DHCP for voice & data in the router where only limited users (around 30)are operating. We dont have IT assistance in t...

HSRP problems - Collapsed core design

Here's the diagram of what I'm working with.PC 101 can ping PC 201 and vice versa. So InterVLAN routing is working.If I break the link between ALS02 and CLS01, HSRP goes nuts.show standby brief on CLS01 shows:vl101 active, local with the remote node ...

span & rspan together

i tried to configure RSPAN & SPAN as source in same monitor   session,  i get below error. is that mean we cannot configure SPAN  &  RSPAN as source in same monitor session "% Cannot add RSPAN VLAN as source for SPAN session 1 as it is not a RSPAN De...

HSRP and L3 Switches

Have 4 switches a mix of 3560 and 3550's in a test lab.test-sv1 and test-sv2 connected via dot1q. Vlan 2 is setup on each switch withtest-sv1 as 192.168.31.2 and test-sv2 as 192.168.31.3 and a standby 1 ip 192.168.31.1.test-sv3 and test-sv4 connected...

Resolved! Access issue of cisco 2811 router

Hi Dear,I not able to access cisco 2811 router (AC operated)  through console port when I try to access it by selecting COM Port, but I  able to access by selecting the TCP/IP option.Please assist to solve this problem.RegardsRahul

Two MST instances, enabling Root guard

I have 2 3550 12G switches that I use as core fiber switches.  Switch 1 is the primary for 1/2 the VLANs and Switch 2 is the primary for the others using MST with 2 instances (I am not including the default 0 instance).  I am using HSRP to provide re...

ngthen by • Level 1
  • 2307 Views
  • 3 replies
  • 0 Helpful votes

Resolved! 1841 and DHCP issue

Hello,I am not sure if this is by design or not but I have dhcp running on my 1841 basically with a 192.168.1.1 - 192.168.1.255 pool.  While I do have set excluded ranges I find that the system does not look for any open IP's once it reaches that las...

rkovelman by • Level 1
  • 821 Views
  • 5 replies
  • 0 Helpful votes
View All
Review Cisco Networking products for a $25 gift card