Switching

Hi,SUP2T should now natilely support VPLS, but I nowhere can find scalability infos about VPLS supportI saw a presales preso where they mention VPLS-support up to 16K VPLS-Instances but as well on CCO the info that just 4K instaces are supported unde...

Hi Forumers'Have a complicated situtation with IOS selectionCusotmer site current C6506-E with SUP 720-3B, current moduel attached to it with ACE10-6500K-9, system running on A2(3.0)Now user would like to revamp their core network and want to invest ...

I have 3750 core/distribution switches with routing enabled in two offices connected with copper link and L3 port channel interfaces. NewOffice#2 has moved about 5 miles farther away from office#1 and I have to deploy new core/distribution switch con...

Hi,I have two  layer 3 switches C3560 and C3750 Cisco switches with ios version "ipservices-mz.122-35.SE5".Now with the current ios version, these layer 3 switches are not supporting object group.so my question is , do i need to upgrade the ios, for ...

I have a 6500 and I would like to enable IP accounting on a wan interface.  I have done the following on the interface level C6K(config-if)#ip accounting output-packetsand the switches gives me :Accounting will exclude mls traffic when mls is enabled...

I am having one Cisco ME 3400G-12CS switch with 4 NNI port & 12 UNI port.I want to convert all UNI port to NNI to as meet my client requirements.Please guide me which Metro IP Access Image IOS  version is required to convert those UNI port to NNI.Tha...

Hi all,I have LAN switch running HSRP   and it connected to WAN router directly.Problem is whenever i ping any internet sites it shows first ping dropped.3550SMIA#ping 4.2.2.2Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 4.2.2.2, ti...

Hi, I am a networking student and was playing around with a  Cisco 2800 series router. Couldnt figure out the pwd or user name so was  following these steps from this KBhttp://www.cisco.com/en/US/products/hw/routers/ps259/products_password_recovery09...

Hello all,I am about to add 2 addtional links to an existing spanning tree topology so each distribution switch goes directly into the two cores.  We have 4 6509s,  2 for the core and 2 for distribution.   There are 2 etherchannels from each distribu...

HiI am totaly newbie to cisco routing, but i have some basic knowledge about routinghow do i configure the new asa 5505 to be as a router as shown in the diagramnote: the isps' routers placed in head office. but i cannot change the configurations of ...

Hello,we have the following strange behaviour and I would like to know how to troubleshoot further on.We have two 6509 switches with one WS-X6704-10GE module in each of them. There is an optical cable between the two switches plugged in  WS-X6704-10G...

Dear All,             I have stacked WS-C3750E-24PD with TenGigabitEthernet ports configured under ether-channel. It has c3750e-universalk9-mz.122-55.SE1.bin IOS installed on it.One of the TenGigabitEthernet ports, goes to err-disable mode with follo...

Hi, I am trying to get a C2960-8tc-L  linked to a sge2000p via the Gbic ports using GLC-SX_MM gbics but having no luck.Are these compatible and should I need to configure anything?

Access-group only allows me to set the mode.access-group > mode > prefer > port > int g2/1Those are the only options available to me, it doesn't allow me to go.ip access-group <name> in or outoraccess-group <name> in or out.I realize the commands may...