hiconsultation, kron commands configure its policies without problems, the only thing that happens to me is that I created the file. log without data, you can help me alguin??Thank you.Alan
Guess the web ate half the diagram but well...Five Levels from Top to Bottom:1-Firewall2-Layer 2Switch--Tie Between 2 Cores and Firewall3-Two Main Cores--Pruned Layer 2 Port-Channeled Trunks carry Layer 3 Traffic(Platforms won't support sub-interface...
Hello,One Question...Do i really need to use a port channel for my vsl link ?can i just take one TenGig interface on each supervisorand put the virtual switch link ... command on each interface... without creating the Port-Channel ?thanks
Hi,Here is problem with switch 6509, I am able to get logging through the ACS password. But when ACS is not in network i am able to get logging through local user name / password.getting enable mode, when type the enable password switch is not taking...
hi guys, there's something would like consult with you all... given the scenario as posted:assume vlan 10, vlan 20 were set on all 3 switches, and it's identical. my question is: 1. will this etherchannel be establish? 2. assume SW A is root bridg...
The scenario is a data center sever farm...A good rule of thumb to prevent excessive cross link traffic in a switched access /routed agg design is to make each agg switch the root and hsrp primary for each vlan. Then alternate this for each vlan so t...
I have 4 subnets (well, really I have quite a few more, but showing 3 illustrates the point): 172.16.3.64/26, 172.16.3.128/26, 172.16.3.192/26, and 10.6.0.0/24. I’m having a problem where the 10.6.0.0 subnet isn’t able to route to the Internet and I ...
Is there a command to limit the number of links that we want bundled in an LACP etherchannel or is the limit always 8 as default? I want to test with 4 ports in the bundle with priority 100 and a 5th port with a higher priority. I want to test how th...
Hi,Switch port is configured as followsmls qosint fast eth 0/2switchport mode accessmls qos trust device cisco-phonespanning-tree portfastDefault Cisco IP phone marks CoS = 5 decimal and DSCP = 46 Decimal.CoS can be used only on trunk frames. So with...
Dear Pros,What could be the cause for the following error message.Loading "flash:/c3560-advipservicesk9-mz.122-44.SE.bin"...@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@fl...
Hello,we have a problem with newly installed Cisco 857w. The router is used to connect to a remote telnet server over a VPN which is not terminated at the 857. The setup looks like this:Client Network 2 (192.168.205.0) < - > Client network (192.168.1...
Hi,My 3550-48-EMI switch keeps rebooting once every few days.At the moment I'm running on c3550-ipservicesk9-mz.122-25.SEB1.bin . I believed the automatic reboot is due to a bug i the IOS as I couldnt see any hardware errors in the log file.However,...
I'm attempting to configure wired 802.1x for the first time, and am having some problems. This is on a 3750 stack running 12.2.53SE ipbase, with ACS 4.2SE.Initially what I want to get working is this.A LAN user with an XP pc gets a prompt to login, t...
I have a 3750 with 20 usersand that 3750 is connected directly to 2960. Every things works wellexcept my 2960 cant reach to my SNMP server which is directly connected to 3750.The 2960 has a default route of 3750, & the clients connected to 2960 can r...
