Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 

Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

Start a conversation

Resolved! 6509, line card error

Hi Everyone,I have a switch where one of the line cards went down but is now back up. I just want to know what might have caused this. Thanks for your help!output:Feb 18 04:45:34.012: %SYS-5-RESTART: System restarted --Cisco Internetwork Operating Sy...

Resolved! EIGRP Stub with Dual Remote Routers

Hi All,I need some technical help for my network, please find the attached prototype network diagram for your better understanding....Topology: Hub and spokeObjective:1) RouterA02 running in pure standby mode, and only activate when RouterA01 down or...

alexloh83 by • Level 1
  • 1430 Views
  • 6 replies
  • 0 Helpful votes

Resolved! WS-X6408A-GBIC 8 port 1000mpbs port speed

Hi, I am planning to use all ports in my 6509 and I would like to inquire if I use all ports in a WS-X6408A-GBIC 8 port 1000mb, do I get a maximum port speed of 10000Mbps on each port? Does this share a backplane or the module has it's own?  thanks!

VS-S720-10G Card (6509-E)

What is the ASIC acceptable Temparature range for the VS-S720-10G  card? Please check the current temparature range seen :BRASWSTA01Temparature recorded : module 5 outlet temperature: 39C  module 5 inlet temperature: 25C  module 5 device-1 temperatur...

Resolved! 3 routers lab 1 connect to DSL router.

I am bit new to cisco and i am learning CCNA. i have 3 routers with a switch and pc connected to the switch. i am working on RIP and i enabled it on all routers and i am able to ping all interfaces/devices (2950 switch, 2500 & 2600 routers)my current...

Bhavesh30 by • Level 1
  • 3441 Views
  • 1 replies
  • 0 Helpful votes

Resolved! Low Memory on Cisco 837 Router

hi experts,i have a cisco 837 router and having this syslog:*Mar 1 01:39:10.615: %SYS-2-CHUNKEXPANDFAIL: Could not expand chunk pool for ipnat entry. No memory availablei tried to do a show run but can't only a show start can view the router's config...

Resolved! Speedtest on Cisco 877 ADSL Line

hi experts,just out of curiousity, i did some speedtest on our ADSL 2 meg line. i tried to speedtest my connection 3x (see attached) but never attain 2meg max and download speed varies everytime. can someone shed some light on this? is speedtest reli...

Router on a stick config

Hello:I have a 2821 router connected to a 2950 switch.  On the 2821 I configured sub-interfaces.  On the 2950 I configured 4 VLAN's.  The port that connects to the router I configured as a trunk port.  The problem I am having is on the 2950 it will o...

HMidkiff by • Level 1
  • 3121 Views
  • 6 replies
  • 0 Helpful votes

VTP server switch failure

I have 4 switches in a network and the server that is operating as the VTP server has failed, but all the other clients still have my vtp information, when I replace the switch, how do I get my VTP information back on the new switch to get the vlan i...

ehinkle27 by • Level 1
  • 2449 Views
  • 4 replies
  • 0 Helpful votes

CSS- MGMT IP - ROUTING

Hi AllJust a quick one.I have a CSS 11501 (7.50) and have configured an IP address for the management Interface. This is now reachable from local subnet, but not from WAN. Apart from the gateway given in the boot statement, do we need to specifically...

Resolved! IOS question

Hi group,We are running with 3560 Catalyst switches and are looking to upgrade the IOS. Currently, we're running 12.2(35)SE5 (c3560-advipservicesk9-m). Can someone give some guideance on choosing an IOS? I do know to look for GD (general deployment),...

View All
Review Cisco Networking products for a $25 gift card