Resolved! Virtual Switching System
what is the Virtual Switching System (VSS)
what is the Virtual Switching System (VSS)
Hi,I have attended an interview they asked me one simple question but i have some dought on my answer.question: A router with single interface connected to L2 switch, we want 5 Vlanswhere do we create the Vlans?where to add the route for intervlan co...
Can anyone tell me if there's a problem with lights on a switch (Model Doesn't Matter, Different VLANs) or I should say every switch blinking fast?Thanks In Advance
1) The lowest prefix possible is /8 ? Or we can go further down ?For instance could we summarize:8.0.0.0/89.0.0.0/8into 8.0.0.0/72) The lowest IP address that we could assign to a host is 0.0.0.1 ?
How do i get it on?
I'm not sure really how to ask this, but I have done some testing in a classroom on my college campus using a wired connection and then a wireless connection. When connected wirelessly, I can see other devices in the network. When connected through...
I currently have to console into one of my switches that uses a private 172.x.x.x address and want to give it a command IP address in order to SSH into it. I'm not sure what the commands would be to do this....any help would be greatly appreciated!!
What is the difference between manual and NVRAM method in VLAN?Vlan130 x.x.x.x YES NVRAM up upVlan192 x.x.x.x YES manual up upVlan500 x.x.x.x YES NVRAM up upOut of 27 vlans that I have, only one (vlan192) says manual.OJ
Is it possible to route NAT traffic to different Servers on the internal Netowrk based on the source IP on the external(internet) side.I want to route traffic from different source countrys IPs (which I hace the ACL for) to different internal Web ser...
I am looking to create a secure vlan where only specific vlans (or hosts) can access it on a given port. For exampleint vlan10 ip address 192.168.1.1 255.255.255.0And only the following can access it:192.168.20.0\24 port 3389192.168.30.0\24 port 22,...
Hello,Has anyone had experience on the 1811? I have installed one and from then on I could not print to my network printers. I can still ping the printers but when I send print jobs, they do not respond.Thanks!Oliver
I have a 2960 switch in a production network. the port fa 0/3 is reporting 99% utilization on the link. This interface connects to an unmanaged layer 2 switch. Is there anyway to find out which IP address is hogging the port?
HiPlease let me know if anyone ve successfully implemented DHCP server on a cisco Switch/Router for the IP Phones [Non cisco].
Hi,To start out with, I am new to Cisco. I have setup other routers without too much trouble, but I'm stuck with setting up an 1812. I have a few problems, the most important is 2 isp connections to fe0 & fe1 for failover. I used the SDM to config...
I've inherited management of a shared fiber line I'm now the only one administrating itâ¦The line consists of 5 3550-12g switchesâ¦My issue is one of the line participants has a port going to his private network set up as a dot1q trunk I cannot see...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-24-2024 02:27 PM | ||
04-23-2024 02:53 AM | ||
04-19-2024 05:58 AM | ||
04-17-2024 03:50 AM | ||
04-15-2024 06:06 PM |
User | Count |
---|---|
11 | |
11 | |
10 | |
9 | |
6 |