hi,a Cisco 3560 switch (WS-C3560-24PS-S) has following scalability feautes Throughput : 6.6 MppsBackplane Capacity : 8.8 GbpsCan anyone explain this ?thank in advance.regardsRajib
hi,a Cisco 3560 switch (WS-C3560-24PS-S) has following scalability feautes Throughput : 6.6 MppsBackplane Capacity : 8.8 GbpsCan anyone explain this ?thank in advance.regardsRajib
Hi, I need some help configuring a 1811 for routing 2 networks and IPS. and a ASA 5505 for Firewall, content filtering and vpn.Right now I have them setup on a test lan. I have the 5505 and content filtering working , but I am having problems with ro...
For monitoring purpose, I need to configure a Span port in 7200,the source port will be 02 Giga ports and the Destination 1 port Gigabit - The total traffic is less than 1GB . Anybody could Help me find the "Span" Command documentation ? TKS
We have an issue with Ghost server getting over vlans (layer 2). This is using Mulicast, Directed Broadcast and unicast. There are no access lists or any other security hurdles between them. It works when it's on the same vlan (obviously). Also, ...
I'm trying to mapp out a network and I have a catalyst switch I need to access. The only information I have is that it is not ip addressed. It is accessed through port 49 VL220 I have the password but don't know how to interface with it with out a ...
With the following:interface Loopback0 ip address 192.168.199.1 255.255.255.0interface Vlan1 description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$$ES_LAN$$FW_INSIDE$ ip address 10.0.0.254 255.255.255.0interface Virtual-Template1 type tunnel tunnel mode i...
Hi,I am running into a problem where I have created 2 separate VLANS, and would like to have communication for some device to communicate with other devices in other VLAN on a single 3750 switch.Here is what I've donecreated VLAN 10 and 20SVI VLAN 10...
I have a c3524 xl that out company no longer has the password for that I need to start over with. How to I take the switch back to default so I can reconfigure it.
Guys,We have 2 CoreSwitches 6509 one is already configured and activated. Our goal now is to run and activate the second CoreSwitch and implement the HSRP/Redundancy. So in case the active CoreSwitch (Primary) is down the secondary will be up.Any con...
can anyone provide me w/ subneting tips and so .. I do know my way around the sw and rt but, I could not master the subneting, anytime there is a senario I struggle..:-( pls help Thanks
Hi to all,We have six Catalyst 2950 switches. We would like to install a Backbone switch for these switches.Which device do you think that would be the most appropiate? Maybe a 3750 switch would be enough?Thanks.
We have 2821 router and I have added VWIC2-@MFT-T1/E1 card. I am unable to see it in the config. I did try adding the command card type T1 1 0. i do see the cardin the show ver. Thanks
We enabled VTP and started using it shortly after our new infrastructure was put in-approx 1-1/2 years ago. However we did not enable pruning.Would enabling in now cause any problems. We have approx 25 VLans that really at this point aren't being u...
If my ISP gave me: 24.24.12.138 / 255.255.255.248 - giving me a range of 24.24.12.138 - 24.24.12.142In order to get mutliple IP's to work on an 871w. Would I?Interface FastEthernet 4ip adddress 24.24.12.138 255.255.255.248ip address 24.24.12....
This is a stupid question, but I dont have time to research....Is "serial 2/7:0" a physical or logical interface? I believe it is physical, but the ":" always throws me for a loop...been a while since I messed with this type of serial card.ThanksVL
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-24-2024 02:27 PM | ||
04-23-2024 02:53 AM | ||
04-19-2024 05:58 AM | ||
04-17-2024 03:50 AM | ||
04-15-2024 06:06 PM |
User | Count |
---|---|
11 | |
11 | |
10 | |
9 | |
6 |