Hi Guys,I have a 2948g-ge-tx switch. It says the supervisor module has failed. I dont have physical access to the switch and form the web I found out that it is a fixed configuraiton switch. show moduleMod Slot Ports Module-Type Model ...
Hi Guys,I have a 2948g-ge-tx switch. It says the supervisor module has failed. I dont have physical access to the switch and form the web I found out that it is a fixed configuraiton switch. show moduleMod Slot Ports Module-Type Model ...
Hi,trying to set up Qos on a 2960. What i want to do : Tagging port Fa0/4 to Cos 5I've done this with 2950 EI but it doesn't work witch 2960Here's my configurationmls qos map cos-dscp 0 8 16 24 32 46 48 56mls qosinterface FastEthernet0/4 description ...
I have an exsisting 3750 and will be adding a second via the stack cable. I realize that they need to run the same code. I should power them off, hook them up, then boot them. I also realize that the interfaces will change IE from fa 1/0 to fa 1/0/1 ...
Hi,What is the behavior a PVST environment when a router "sub-interface" configured with a particular VLAN is shutdown/brought up. The router connects to a c2950 dot1Q trunk port configured for few VLANs.When there's a change of the physical interfac...
Hi all, When multilinking say 4 x isdn bri's, when I create the dialler interface to dial them all, on each bri, can I use no ip address, so it will use the ip of my dialler ?
Hello sifus,I would to get some info for overutilised trunk connection.wondering what could be the root cause for it.I am seeing multiple frame drops as well.Other trunks for this dist switch with same configs are running fine wihtout no problems.Cab...
CD-3560-EMI= will be reflect to which IOS?DHarmesh
we have a numbers of swtich and want to set with same vlan domain. Question is some model of C2924-XL vlans number maximum VLANs supported locally : 68,while other 3524 switch have maximux vlans 254.I worry when I form the vlan domain that will crash...
Hi there,I've read a fair bit about flow control and although on the surface it seems quite obvious it is actually anything but that. I've got a 6500 switch which has 3 Exchange servers connected to 3 of its GigabitEthernet ports. I've set the swit...
I am trying to configure a 837 router to connect to an ADSL circuit (PPPoA) with a PIX 515e behind it. I have been given a 5 public IP address to enable this.I just want the 837 to provide ADSL connectivity, with all access (NATing, IP Sec etc) done...
Hi,I have Cisco 6509 switch. I have to create a /28 network. I have created a L2 VLAN & a L3 VLAN. I am not able to ping to the switch VLAN IP. What might be the problem ?
Hi, all.I am struggling that if SUP engine can be configured as a active with manual configuration.If I equipped two engines, SUP automatically decide to elect a active module. But I want to know which slot is higher between two slots.And how can i c...
I notice that the 2955 is a hardened switch. We require this level of ruggerdisation but with power injection and gigbit LH SM module. Ideally a 3560 8PC would be great. It must survive 60degrees of temperature. Also is there any wireless which will ...
hi all, i am faced with a very strange issue, ( i nearly pull my hairs out ), see i have a 1841 router with HWIC-4ESW installed. on Fa 0/0/0 i have a ADSL connection so i gave ip to int vlan 1 and my link is active now. my task is to limit ALL the tr...
Hi,We have an 2811 which uses crypto and nat.This router consumes all of its IO memory over time and starts generating alloc failures.IF we compare the memory usage of the io memory to a healty router with a comparable config it had several 65Kb memo...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-24-2024 02:27 PM | ||
04-23-2024 02:53 AM | ||
04-19-2024 05:58 AM | ||
04-17-2024 03:50 AM | ||
04-15-2024 06:06 PM |
User | Count |
---|---|
11 | |
11 | |
10 | |
9 | |
6 |