Resolved! routing 2950
Hi, We have a Cisco 2950-24 switch on a remote location with single vlans.Is it possible to do routing between vlans on that switch? Best regardsJorg
Hi, We have a Cisco 2950-24 switch on a remote location with single vlans.Is it possible to do routing between vlans on that switch? Best regardsJorg
HIi just wanted to know what is this command used for at console or vty line"timeout login response 4"and the second command"log synchronous "plase helpThanksGursaran Abott
We have issued a "show log" command in telnet session of Catalyst 2960 but it didn't display the same information we issued in console.
hi,wich method is better for controling vlans on large LAN? allowed vlan on trunk ports or vlan pruning?
Hi all,Just upgraded a Cat3560 to IOS ver c3560-ipbasek9-mz.122-44.SE.bin and a Cat2960 to c2960-lanbasek9-mz.122-44.SE1.bin respectively. Just after upgrading I discovered there is a later release for each of these models. Now, however, I cannot g...
my cisco 3745 shows following output when done 'sho version'... this is part of the whole output....==>DRAM configuration is 64 bits wide with parity disabled.151K bytes of non-volatile configuration memory.31744K bytes of ATA System CompactFlash (Re...
Hii am trying to learn cisco and i have passion to learn I know wat i am asking is gonna be really long and complicated but i would really appreciate any help to get me startedMy question isI have three 2600 routers with two wic 1t cards in each of t...
I bought the AdvIp IOS which requires a memory upgrade. So I popped in a 32meg flash. Now there's no OS, I get ROMMON, can't get router#boot just ROMMON. TFTP doesn't work because it seems like the interfaces are disabled (tried all the switch ports ...
hi all, i was confused by the use of deterministic-med in bgp so a guy here helped me out with a doc which was awesome ! i know how it works now, but i dont understand why will i need it at all ? actually i am preparing for CCIE, so i dont understand...
Hello all, first time using Cisco and I'm faily noobish so please bear with me.I have a 2wire DSL multifunction unit and a Cisco 831 behind the 2wire. I'm having a problem getting the network running properly.As currently configured, from the Cisco ...
Hi all, has anyone got a doc on how to set up the wireless lan controllers ?
Hi,Please refer the digram a clarify few doubts;1) Is the connection between router to router is necessary? What traffic is passing through that. The routing is doing by Switch.2) Which layer should be the link between router and switch be ? (L2/L3)....
A network audit recently found 48 of 155 routers using eigrp configured with the default auto-summary. They are contained within a single eigrp AS and the network seems to work fine, most of the time. What's the potential impact of having 31% of our ...
I just received a brand new 4506-E with a supervisor IV card. I also have a 48 port gig Ethernet card. I powered it on and there are no status lights on any blade. The fan light is green as are the power lights. My VAR sent a new supervisor card ...
Is there a way to make a change to the start-up config and not the runningConfig on a 3560I need to make changes ONLY on the interconnect ports and this needs to be done remotelyI would like to make the changes and set the reboot times I know if I tf...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-24-2024 02:27 PM | ||
04-19-2024 05:58 AM | ||
04-17-2024 03:50 AM | ||
04-15-2024 06:06 PM | ||
04-12-2024 05:48 AM |
User | Count |
---|---|
11 | |
11 | |
10 | |
9 | |
6 |