We are getting the following error. This is a newly created rspan vlan. NJ02GA03E1S02> (enable) set vlan 999 3/16Vlan 999 is an RSPAN vlan.Failed to add port 3/16 to Vlan 999.NJ02GA03E1S02> (enable) --------------- NJ02GA03E1S02> (enable) show ve...
We are getting the following error. This is a newly created rspan vlan. NJ02GA03E1S02> (enable) set vlan 999 3/16Vlan 999 is an RSPAN vlan.Failed to add port 3/16 to Vlan 999.NJ02GA03E1S02> (enable) --------------- NJ02GA03E1S02> (enable) show ve...
What is "spanning-tree optimize bpdu transmission". I have this in a bunch of my switches and haven't found a good reference for it. TIA.-John
dear Netpro!what this Mean?In the Network EIGRP 1 is configured , you must transit the EIGRP to ospf smoothly.many 10xs
have a 3640 router and a switch with vlans in it. I want to use the (router in a stick method) but, when I create the sub-interface to specify (vlan-1) as the native vlan, the sub-comand (native)dos not appear after I have put (Router(config-subif)#...
I am trying to create an etherchannel between non adjacent ports on a 6509 running catos and a 4507 running ios. The switches are configured as follows:Cisco 6509 running CatOS ver 8.4(5)set trunk 1/1 on dot1q 1-4094set port channel 1/1 mode onset t...
hello, am just a newbie at the early stages of my ccna, my ios command line interface does not accept the show interface status command. is this normal with all simulation software as i downloaded mine free from the internet.thanks.
Hi !is there any SFP-Transeiver (CAT5) available which supports 10/100/1000 ?Unfortunately the model we got - obviously is 1000-Base-T (fix) .On Cisco website I could not find anything.Could you please help me ?thxhans
I'm looking for any example code of the following, I think I know how to handle this, but I'd like to see some kind of example to go by.I currently have 3 sites. Each site has at least one 3560 switch and each site has a 2800 router. (One site has ...
Problem in R1841 has 2 adsl , i want to use load-balance, now i config it but it not work. Client can access web but sometime can't access , when client use "nslookup" may be have time out , when client use ftp to ftp server can't access or so long t...
(this is for ports 17-18 config in group 1)switch(config)#int fa0/17switch(config-if)#switchport mode accessswitch(config-if)#switchport access vlan 1switch(config-if)#channel-group 1 mode activeswitch(config)#port-channel load-balance src-mac(this i...
HelloI am using cisco call manager 4.1(3), problem is IP phones specially 7902 are connected with Linksys & cisco 3750,2950 switches but in router log it is showing "%CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on gigabit ethernet port " thou...
Hi I have OSPF Route summarization up and running on my ABR'sBut for some reason when I do a tracert from other router that is not part of the same area this going by other several ways where the interfaces has other metrics.So if the summarization ...
I have a new out of the box Catalyst 4503-E. It has ISO file in the bootflash of cat4000-i9s-mz.122-25.EWA10.bin. The porblem is it just boots into ROMMON mode and never gets to the switch> mode so I can do the config on the switch. I also get an err...
i have a 2811 with 16 port switch but when i attempt to assign a ip address to fa1/0 i get the message unable to add ip on L2. Is the a reason for this?????help
Hi.I am trying to do an unequal cost load balancing across 2 routers on a remote location(routers 3 and 4 in the picture).The link on router 3 is 2 Mbits and 1 Mbit on router 4.They have HSRP between them in case one of them fails(with router 3 being...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-26-2024 11:15 PM | ||
04-26-2024 09:45 AM | ||
04-24-2024 02:27 PM | ||
04-23-2024 02:53 AM | ||
04-19-2024 05:58 AM |
User | Count |
---|---|
12 | |
10 | |
10 | |
9 | |
6 |