does anyone know a decent tracerouting tool that uses layer 2?Thanks
does anyone know a decent tracerouting tool that uses layer 2?Thanks
I'm looking for suggestions on troubleshooting a link to our datacenter that has intermittent connectivity and speed issues. The link to the datacenter is approximately 30 miles in distance so even on a good day there is 3-4ms of latency. At this p...
Dear All,I have a Cisco 6500 catOs Version 8.2(2), the rack where 6500 is placed is a disaster a lot of rj45 cables it seems like a jungle.The 6500 has the following modules:N2 WS-X6K-SUP2-2GE with WS-F6K-MSFC2N1 WS-X6224-100FX-MTN4 WS-X6248-RJ-45N2 ...
Is there a way to configure or change a Device's name (Not part of CDP) on a Catalyst 6509 switch interface?
All- I am implementing TACACS across the network.all the IOS's, Pix's and VPN solutions are complete.The problem is the CAT OS switches,i am testing with a CATOS 2948G switch.see the config below.Cisco Systems, Inc. ConsoleOMKSW02 (Cisco Catalyst 29...
Hi Everyone, Our network is currently being bogged down and we're trying to get to the bottom of it. I enabled netflow on the router and see alot of information from the output. I do not have a server to dump the information to, so I am just tryin...
In classful addressing, class A networks would allow up to 16,777,214 hosts be attached to the network. In reality, how was this managed? This many hosts were attached to a single LAN? Was the traffic so light that this many hosts could be attache...
Hi guys,I know this is an easy question but i've had a brain dead moment and can't for the life of me seem to think of the answer: I'm running a Catalyst 3550 in a lab environment and i've put in the following config:switch(config)#int loopback0switc...
Is there somekind of tutorial to configure a cisco 831 router as a dns server ?. I am quite lost with all the possibilities.Thank you !!
Hi experts,I was just wondering, whenever i do a ping, I usually get a timeout on the first ping then the next ping will be fine.is this normal?Im using Cisco 3560,3750,6500, and ASA5505.tia
what does the "sub" mean in the sh ver outputcat6509> (enable) sh moduleMod Slot Ports Module-Type Model Sub Status--- ---- ----- ------------------------- ------------------- --- --------1 1 24 1000BaseX Ethernet ...
Hi.I have a device which sends voice over IP packets marked with ToS only (ToS=3).All packets pass through a 2955 switch.From the configuration guide i see that the switch supports only CoS and DSCP.How can I forward the Voice packets and still keep ...
Does anyone know if there are significant bugs with IOS release 12.2(25)EWA7 and Spanning-tree protocol?I am having problems with loops and have ruled out most other possibilites.Thanks.
we're creating an etherchannel between the two 10GE ports on the 6509's and I was wandering if there were a conclusive way to verify that the Layer 2 was working between these switches? I was thinking of may be pulling the cable off one of the switch...
Hello Community, I am new to the Cisco world and I need a few tips and go to places. I have been trying to figure this out on my own and after one week of clicking around I need help.I bought a ASA 5505 recently from newegg.com. Comes with ASA versio...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-24-2024 02:27 PM | ||
04-19-2024 05:58 AM | ||
04-17-2024 03:50 AM | ||
04-15-2024 06:06 PM | ||
04-12-2024 05:48 AM |
User | Count |
---|---|
11 | |
11 | |
10 | |
9 | |
6 |