How can I force a 2960 switch to use the default gateway parameter.?I try with the command :ip defautl-gateway 10.10.10.1but the switch never use it.Thanks in advanced
How can I force a 2960 switch to use the default gateway parameter.?I try with the command :ip defautl-gateway 10.10.10.1but the switch never use it.Thanks in advanced
Does anyone knows the mib ID of the following command "show mac-address multicast count"? I am able to run this command on my switch but when i use GetIf to retrieve the value, i am not able to find the value.
Hello,we have CSM-SSL Module installed in our core 6509 switch, we use it to provide SSL and load Balance for our websitealso we use it to rewrite all http traffic to be https secure traffic.so anyone type www.abc.com in his browser it will redirect ...
Hi.I need to get POE to a Cisco 3750 switch that is connected by optic fiber.Anybody knows if there is any Csico product to do it?.Thanks for advance.
Dear all,I'll miss the introduction and proceed to explain my problem.I have two WS-C3750G-24TS catalyst switches in a stack. Couple months ago I found out an issue with them and two days ago understood with my friends at work what exactly the proble...
dears,when i lunched SDM i just got this data with out GUI or graphs interfacesCisco SystemsAccessing Cisco 7204VXR "router-01"Show diagnostic log - display the diagnostic log. Monitor the router - HTML access to the command line interface at level 0...
Hi Guys,I have some doubts abour qos.What do we mean by queueing,is it the way router forwards the traffic from the interface i m right in thinking this.By defaut how many queques are there in the router.ThanksMahmood
Im planning to use a 4507R with redundant Supervisor Engine II-Plus-10GE's but only want to install one X2 GBIC in the Active Supervisor. Will this work? I understand if the Active SUP fails I will lose the link.
Hello,we have an online system used to provide our service to the customers, we used 2 cisco 3845 routers withHSRP configured on both of them.one router is the primary and the second is the secondary connection to provide redundancy.there is Cisco AS...
hiwe have server on DMZ area (front exchange) which we need to make it able pinging a server on protected lan (and open ssl tunnel) .the problem is i coudlnt make my server on DMZ area which sec50 able to ping the servere on my protected lan how to d...
Guys, is the Dynamic configuration tool pretty reliable? I have to configure a bunch of 6500's & 4500's.Also, is there a power configurator which allows you to fill in modules into a 6500 like POE, etc and it'll tell you exactly what power supply you...
we want to enable dynamic arp inspection to disable ARP poisoning in our Local LAN. We are using cat 2960 series switches. I am unable to locate any commands relevant to DAI in cat 2960. we are using the latest software image.Appreciate if anyone can...
The l3 port channel config between 2 switches are follows Sw1, Interface range gig 1/19- 20 No switch port Channel-group 12 mode desirable Interface portchannel 21 Ip address 192.168.10.1 Sw2 Interface range gig 1/19- 2...
WE have a 6500 and are spaning a port with one device. we are adding another device and I was wondering should I just another line with the same session for the destination interface or is it recommned to have a separate session. Thx
hi,After telnetting cisco 3750, i cannot proceed to configuration mode. Help is requriedThanks in advance.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-27-2024 12:39 PM | ||
04-24-2024 02:27 PM | ||
04-19-2024 05:58 AM | ||
04-17-2024 03:50 AM | ||
04-15-2024 06:06 PM |
User | Count |
---|---|
11 | |
11 | |
10 | |
9 | |
6 |