Hi,I am new to port security and was wondering what the difference was between the last known last-src-addr and secure-scr-address?Thanks all.
Hi,I am new to port security and was wondering what the difference was between the last known last-src-addr and secure-scr-address?Thanks all.
Where is NVRAM on a switch? Is it just an EEPROM on the device or is it really FLASH? Just trying to figure it out. Had a router power supply go bad and replaced the device via SmartNet. I've moved the RAM and FLASH over to the replacement, but t...
I have a WS-C3524-PWR-XL I'd like to bring in to temporary service, and need to migrate it from STP to PVST. Does anybody know the command(s) to do this? Usually it's "spanning-tree mode pvst", but even with the latest IOS I don't have that option:...
I'm running IOS v12.2(18)When I'm trying to configure the interface, i'm expecting to see the commands "dot1x guest-vlan" and i don't see it. Everything is set up globally and i have the port-control auto set. There is also no auth-fail vlan to set f...
i am trying to find the equivelant ios commands for catos. do they exits?snmp-server locationsnmp-server contactsnmp-server chassis-idthx
Hi, Can anyone let me know if ICMP is a transport layer protocol? I was thinking its a network layer protocol.Thanks,Radhika
I am VERY new to networking, in that this is the first time I've ever tried to install a new switch... So my question is, we currently have an existing 3560-G switch and we received a new one, along with the SFP cable. Can I simply plug the new one, ...
I have so many vlan & vlan interface in my network, now suppose I am sitting in vlan 2 & using vlan-2 interface IP address as default gateway & working fine.Now I change my default gateway & give vlan-3 Interface ip address as default gateway. Again ...
I installed a new VWIC2-1MFT-T1/E1 card in my cisco 3825 router, and the router does see it, but I am unable to configure the "controller T1". 2 Gigabit Ethernet interfaces60 Serial interfaces8 Channelized T1/PRI ports1 Channelized (E1 or T1)/PRI po...
Hi there,Guys, I dont have the hardware to hard, but does anyone have the default config for these two port queueing types?Also, in CatOS, you can do a wr term all and get the defaults, can you do this in IOS? Many thxKen
Hi people,I want to know how to interpret properly this command?What am I supposed to determine from this command?Regional1 Con0 is now availablePress RETURN to get started!Regional1>enableRegional1#show ip eigrp topologyIP-EIGRP Topology Table for A...
HiI'm monitoring a vlan via rspan, but I'm seeing duplicate packets. The rspan is configured to monitor both incoming and outgoing traffic from th e vlan. My question is what can I do to stop the dupliate packets?Thanks in advanceDan
helloI configured vlan 1,2 and 3 on switch cat2960 ios: C2960 Software (C2960-LANBASE-M), Version 12.2(25)SEE2.I connected the switch f0/1 port configured like a TRUNK 802.1q, to a cisco2610 router with ios : C2600 Software (C2600-IS-M), Version 12.2...
Hi people,Can someone explain to me, how can one interpret or distinguish the routes from the routing table? (eigrp,ospf)
Hi,i am trying 802.1x (peap) over Wire.equipment-acs 4.0-3750 switch w 802.1q trunk-client windows xpthe problem i am getting is my switchport is getting the desire vlan.acs - Authen OKswitchport - authorisedvlan - 1 (correct vlan should be '40')ACS'...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-24-2024 02:27 PM | ||
04-23-2024 02:53 AM | ||
04-19-2024 05:58 AM | ||
04-17-2024 03:50 AM | ||
04-15-2024 06:06 PM |
User | Count |
---|---|
11 | |
11 | |
10 | |
9 | |
6 |