Switch 2950, do I need manully to insertthe Clock timezone - local time
Switch 2950, do I need manully to insertthe Clock timezone - local time
now ,when started the 6509 auto enters into ROMMON mode. when started ,it prompts:(slot 5 is sup-720 moduel)FABRIC-SP-5-CLEAR_BLOCK: Clear block option is off for the fabric in slot 5.00:01:18: %FABRIC-SP-5-FABRIC_MODULE_ACTIVE: The Switch Fabric Mod...
Hi all, I was looking at my book yesterday on frame relay, is it right that if you congigure it on a serial interface ie s0, you only need to put the encapsulation in if it supports inarp? can we do this if we have multiple dlci's or would we have to...
Hi all,I am preparing for the CCNA exam and currently studying STP. I have a problem in understanding Designated switch and designated port concept. I have read several documents and books, but unfortunately none of them helped me to understand this ...
I would like to restrict 192.168.1.x in a routed network from only getting 512 MB of Internet access while users on 192.168.6.x have full bandwidth access. Is there an easy way to do it? Both IP addresses are subinterfaces on my LAN side, and the WAN...
Hi all,I currently have a 2821 router that i wish to add another T1 card to with anoter service provider. I am attaching equipment on the unused ethernet interface and wish this equipment to only use the second T1 interface. are route maps the way ...
hi, We are planning to have 6513 at our data center along with the FWSM , IDSM and DFC modules . i have a question regarding the same : I plan to use MSFC in front and then fwsm .. 1.in this case does all of my dfc will be like L2 switches and even t...
Hi all, when configuring access lists in my router, what is the differenct if I use, access-list, or ip access-list ?cheers
Few of the ports on 3750 went in to error disable mode while configuring port channel. config as goesinterface Port-channel1 switchport trunk encapsulation dot1q switchport mode trunkinterface GigabitEthernet1/0/45 switchport trunk encapsulation dot...
I'm almost pulling out my hair trying to connect a Linksys SPA942 IP phone to use the inline power of a Cisco catalyst C3524-XL-PWR. The switch has been set up as per the procedures for Cisco IP phones. However when I plug in the Linksys phone it doe...
I have to upload IOS on 1721 router kindly suggest me any link as I have removed the old IOS and copied the new one but never rebooted as want to check 1st from which IOS it will boot
Hi Im facing the problem of High utiliZation (99%)how i can resolve the issue i have take some logs which shows this but im not able to understand the logs
We have a Cat 5505 with a Sup III module, but are unable to access it through the console port. We have the correct cable as we can see it booting on the output dumped to the terminal client, but it will not take any input, not even a break code. It'...
Hi all, when we talk about e1 lines, are they basically an ISDN pri circuit?
If I connect connect two equipment as below. The result is I can ping the 2924 ip from 3560. Why ? Why 2924 fast ethernet port is vlan 1 but 3560 fast ethernet port is vlan 2. the connection is also success ?2924Int fa0/1 !Int Vlan1Ip address 10.10.1...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-24-2024 02:27 PM | ||
04-19-2024 05:58 AM | ||
04-17-2024 03:50 AM | ||
04-15-2024 06:06 PM | ||
04-12-2024 05:48 AM |
User | Count |
---|---|
11 | |
11 | |
10 | |
9 | |
6 |