Hi all,I wonder if there is a command to see the number of dropped packets in Cat9k.I cannot find the corresponding command to this one used int Cat3k:show platform port-asic stats drop Regards,Urs
Hi all,I wonder if there is a command to see the number of dropped packets in Cat9k.I cannot find the corresponding command to this one used int Cat3k:show platform port-asic stats drop Regards,Urs
I am having a problem with QoS on the 3850 platform. It seems no matter what I do I cant get the switch to properly mark traffic. Basically, I have VPN users that use jabber for phone calls. I have successfully configured QoS on 2960x and 3750x switc...
Hello, As already maybe you guys know Nexus 9300 has port-channel limit which is 256. https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus9000/sw/7-x/scalability/guide_703I77/b-Cisco-Nexus-9000-Series-NX-OS-Verified-Scalability-Guide-703I7...
Our organization has recently had 2 Cisco ISR 4331's fail with identical symptoms. Has anyone else run into a similar issue with this model, and/or do you have any advice on how to proceed? - Both were in service when they failed unexpectedly. No up...
Does C9500 Series support Encrypted Traffic Analytics (ETA) ?
dears plz correct me :When I make copy run start in the default vdc it will effect the changes of that vdc and of the aresources allocations ( interfaces ..memory ...etc )but when u make copy run start on another vdc it will effect the configration o...
hi there...is there any brief about catalyst 9407R switch ios version was not explicit my question belowcisco IOS XE 16.09.03 difference between cisco IOS XE fuji 16.9.1 with best regard
hi allthe switch line card is listed belowC9400-LC-48SC9400-SUP-1XLC9400-LC-24XS thanks
HiI want to see the following packet in a switch debug command.But it didn't work.Communication between devices is good. case 1192.168.50.2 -> 192.168.50.1192.168.60.2 -> 192.168.60.1At this time the ICMP debugs were collected successfully. Case-2192...
Hi, May I know, why 2 different mac addresses of a server are being shown of CISCO 6500E Layer-3 Switch ? One server having one nework adapter (MAC ID : xxxx.xxxx.xx0c) is connected to an interface of Cisco Layer-3 6509E Switch. But on running the co...
Hi community, I think I missed a configuration line for HSRP. The question is, how the multicast-packets of hsrp v2 are communicated if the hsrp members are configured within a physical subinterface. Setup:Fortigate500E Port9 =(like Portchane...
The switch takes about 200 seconds to boot, which is very reasonable. However, after boot is complete, it sits there for 22 minutes seemingly doing nothing until suddenly all links come up and the switch begins passing traffic. During this time, the ...
Does 6800 series and C9300 support autosate feature? If yes, what are the commands to disable autostate on SVI on 6807 and 9300 platform
can I stack a C9200-48P with a C9200L-48P-4X It isn't an option when i go to provision the second switch... not matter which one I make switch 1. I am guessing these cannot be stacked.
I am trying to find a device using IP-Address in my lab, I ran the "sh ip arp x.x.x.x" command and got the mac-address. Later I ran the "sh mac address-table address xxxx.xxxx.xxxx" command, the output shows VLAN number that VLAN has many port-channe...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-24-2024 02:27 PM | ||
04-19-2024 05:58 AM | ||
04-17-2024 03:50 AM | ||
04-15-2024 06:06 PM | ||
04-12-2024 05:48 AM |
User | Count |
---|---|
11 | |
11 | |
10 | |
9 | |
6 |