Greetings All, I wanted to ask for guidance in configuring a cross-stack etherchannel between an isr 4451-X via 1Gbps Fiber to 4 3850 switches in stackwise configuration. I would prefer not to assign an IP address to my port channel. Here's wh...
Greetings All, I wanted to ask for guidance in configuring a cross-stack etherchannel between an isr 4451-X via 1Gbps Fiber to 4 3850 switches in stackwise configuration. I would prefer not to assign an IP address to my port channel. Here's wh...
Hello, See diagram attached. I am planning on implementing the topology depicted on the diagram and wanted to find out if ASAs use BPDUs when their ports are configured as 802.1q ports. Since switch-a and switch-c are connected to asa-a (active) and ...
Hello Cisco Community I have a question regarding how should Exclude vlans from a VPC Peer-Link, Here's the issue I got a peer-link between 2 VDC on a Nexus7k, I got VPC configured, but there's an issue that Vlans on one side doesnt match the same vl...
When configuring IPv6 egress filter on a nexus 3636C-S sw version 9(3)3 got below:core1-gw-new(config-if)# ipv6 traffic-filter ipv6EgressFilter out This platform does not support the IPv6 address match on egressDoes it mean that this is a limitation ...
Hello,I have a system that consists of two 3750 switches.The SNMP manager software sends the switch the 'get request' command with the following data 1.3.6.1.2.1.2.2.1.8.10101 to 1.3.6.1.2.1.2.2.1.8.10128. This is requesting the ifOperStatus of the ...
I am RDP'd to a laptop with a console connection on COM4 to a 3850, I open Putty and each character I type is wrong, inconsistently wrong...for example, the following output of what I get from typing the letter "a" repeatedly: Switch#qu}yyuqy|q~yuy...
I am looking to wirelessly network my house and I have a basic knowledge of networking and can program it.My question is based on the ports use. When you get the package, it comes with an rj-11 a modem and then something that comes out the router an...
Hello, I have 3850 switches with 16.3.6 IOS version.We have Radius authentication for ssh with a local account as a fallback. When i am trying to connect to a switch from any browser i get the below screen I have used Windows AD credentials and loca...
So I recently learned that Flex Links have been deprecated starting with early IOS-XE 16.x, but that there's a new feature called Flexlink+ that's available as of IOS-XE 16.12. When I found the config guide chapter for this feature, the config state...
Hello there, I'm a newbieI want PC VPN, FIDS, Banner, and Client can't ping the server, but the server can ping them, I did the configuration but still they can still ping each other. Can anyone help me, I complete with the softcopy please see what ...
When I SSH from 3650 to 6K it doesn't prompt for username, instead it goes straight into password,and I haven't set any enable passwords on my nexus, I don't even know if that is the case but how do you set enable password on nexus 6K,and one last qu...
Hello, Can you use two SVL links or only one to form a StackWise logical switch? I understand that the requirement is to configure a single SVI (formed as an EtherChannel interface comprising of up to 1-8 physical member ports); however, I was wonder...
Hi All,Planing to buy couple IE4000 switches to one of our projects, I have not used them before, the model that will go with has dual media ports (combo ports 4 fiber/4copper).This is what the data sheet say "Combo ports provide one copper and one f...
hello i got a SUP7-E on yesterday and i have to change diagnostic level minimum to complete. so i changed license level Lanbase to Entservices (this sup's boot image is cat4500e-universalk9.SPA.03.08.07.E.152-4.E7.bin) after reload, license level is ...
I am configuring 4 x Cisco 2960x - 24PS switches for voice . What details will I need before proceeding with it ?These 4 switches will be connected to 3560 Cisco Catalyst switch. There are about approx 60 users .What is the best way to do this ?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-24-2024 02:27 PM | ||
04-23-2024 02:53 AM | ||
04-19-2024 05:58 AM | ||
04-17-2024 03:50 AM | ||
04-15-2024 06:06 PM |
User | Count |
---|---|
11 | |
11 | |
10 | |
9 | |
6 |