Resolved! CUCM vs. VCS registration
Does anybody know where I can find information on the pros and cons of registering video endpoints to CUCM and VCS?Thanks,Mike
Does anybody know where I can find information on the pros and cons of registering video endpoints to CUCM and VCS?Thanks,Mike
I have a situation in where an existing VC call is happening in TMS and i want to add a TCS into that callin TMS, when i go into "add participants" within that call, all i get is the selections of "Endpoints and Rooms | Phone Books | External | Templ...
Is there anyPhone 7961 solution without implementing "switchport voice" immediately at switch port but at the switch before the switch which is directly connected to the phone?(Please see attached diagram. )
Have the 2nd generation of the TCS and running S5.2 firmwarefor some strange reason it is not registering to our VCSboth units are on the same VLANsuggestions?ThanksAnthony
Hi,After starting a conference from MCU with 10 or more participants, for example one location starts to talk, other locations can hear clearly, when one of the other location starts, we can not hear anything at the beginning, after few letters it ge...
I was looking for the old test sites of Tandberg. So i browsed to the online support page on the tandberg site. But i was redirected to a Cisco site.On other pages i found the ip addresses of the test systems. But i was not able to dial them.Are they...
Hi, I have a question about the One Button To Push for the C series endpoints. I am setting up the new network and all the hardware in the latest software. C series endpoints on TC 5.0 and TMS on 13.1.2. According to the release notes, C serie...
If I setup a SIP trunk between a VCS Control x6.1 and a CUCM v7.1.3 cluster with a CUPS-server and CUPC clients.I've enabled Presence on VCS side and configured the SIP trunk for presence but the presence status is not showed on the CUPC clients and...
I want to set the audio/video/signalling traffic in our VCS (Video Communication Server) to the values recommended in the Medianet 4.0 QoS SRND. The recommendations are to mark interactive video and audio the same at CS4, and signalling at CS3.Howe...
Hi,I'm new to VCS Expressway. what would be its intial configuration so that we can make external calls?I've already configure VCS control and it's working great. I'm just new to VCS expressway..please help...
We have a CUBE connecting our CUCM environment to other enterprises via SIP trunks. Is it possible for this CUBE to accept SIP registrations from remote video endpoints and funnel them back to the internal CUCM?Thanks!Jeff
I have a 2901 router with a EHWIC-D-8ESG-P card in it. I have configured a DHCP Pool for the voice vlan but the phones get an IP address from the data vlan. What am I doing wrong..,?ip dhcp excluded-address 10.2.100.1 10.2.100.30!ip dhcp pool Phonesn...
Hi,I've setup TMS to send out email alert but it didn't send out an alert when I unpluged one of Ex60 device that was registered in TMS. why is that? I do I resolve it?Thanks...
Good day, I was looking for a codec series C that could accept a 2 screens set up, I guess It should be one for the DVI out, and the other one in the S-Video out, I was thinking that it had to work with one screen showing the remote camera view and o...
Hi We have deployed the vcs control and expressway solution. For some users the movi client after login disconnects within 5 minutes and takes a long time to reconnect back. All the users are connecting to movi client from the internet segment. users...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-26-2024 08:22 AM | ||
04-25-2024 05:00 PM | ||
03-26-2024 08:37 AM | ||
03-22-2024 10:12 AM | ||
03-20-2024 01:51 AM |