We have recently rolled out a Tnadberg Video Phone.Is the Tandberg phone considered an endpoint in call manager?Can you adjust what bandwidth the phone uses from within call manager?
We have recently rolled out a Tnadberg Video Phone.Is the Tandberg phone considered an endpoint in call manager?Can you adjust what bandwidth the phone uses from within call manager?
We have recently rolled out a Tandberg video phone for testing in branches.We have a MPLS WAN with 9Meg (X6 T1s) at the main site and a full T1 at the branches, including the one with the phone.We also have six other branches utilizing the Main branc...
Dear all, My company purchase: Cisco 2821 Voice Bundle, PVDM2-32,SP Serv,64F/ 256D (CISCO2821-V/K9) and PVDM2 32-channel to 64-channel factory upgrade (PVDM2-32U64). Is it related to channel that can support E1 link? If so, from the above product, ho...
Posted in wrong section. I opened a new post in IP-telephony.Hi,We have a cisco WS-SVC-CMM running IOS wscmm-i6s-mz.123-8.XY7.bin and 1 6 port E1 module inserted.I'm trying to setup a trunk group that I want to assign to 2 E1's but the system does no...
When I am engaged in a call on my 7940 and wish to transfer a call. I press the transfer softkey and the phone resets. If anyone can give me some ideas and or solutions it would be greatly appreciated.
I have a sip dial-peer with destination-pattern 521T sending calls to a GSM gateway (QUESCOM). the normal calls are working prefectly, but when i tried to call 521*333 for example, the GSM gateway only receives 521 in other words the cisco gateway ...
Is it OK to connect a switch or hub to a phone's access port to accommodate multiple PCs hanging off the phone? It was my understanding that a VoIP phone had an internal 3-port mac-address table, accommodating the mac-address of a single PC, the mac...
I need to design a VC solution and I'm struggling to find answers to a few questions: 1) Can Telepresence integrate with MP Express and be scheduled via that? 2) Can Telepresence be used with a Cisco MCU? 3) Can VTA and other 3rd party units (i.e. Ta...
Hello,one of our customers has succesfully setup a few Polycom VSX Endpoints and they are registered to a Gatekeeper.Calls can be made manually in both directions but if a IP Communicator/IP Phone calls a VSX the recent call list will only include th...
I am running dmm and vp 5.0.2with the upgrade to 5.0 I found that there is a new feature that allows you to copy and paste a script from the video part into a website. This provides an embedded windows media or flash player on the page, alot of my c...
I am looking a recommendation on an economical HD video endpoint that supports SIP, Cisco MPX and MCU, any recomendations?
Hi,We have a 3515 which responds really slowly when you http onto it (for admin etc). The processor averages 6-8% utilization but it takes up to 30 seconds to navigate between the tabs. it gets better after a reboot, but soon resorts to being 'slow...
We have IP VTC going from a Tandberg Video Conferencing bridge to a distant Tandberg and it was dropping because of the Timeout settings to I increased the timeouts and it was fine but now it intermittently fails anyone seen this before.
We currently have Tandberg video conferencing units that we use for internal video conferencing. However we need to be able to video conference with other people on the internet. I have been reading about using a 2621xm router as a gateway to do th...
I have a 2611XM with NM-2V and Vic-2xo module. The router runs advance enterprise feature 12.4-21a. The router is able to recognize both NM-2V and Vic-2FXO module but I can not access the voice-port interface mode to configure the FXO. Is there any ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-26-2024 08:22 AM | ||
04-25-2024 05:00 PM | ||
03-26-2024 08:37 AM | ||
03-22-2024 10:12 AM | ||
03-20-2024 01:51 AM |