Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Help Required (Codian ISDN 3240)

Hi guys,

I have a codian isdn gateway that I cannot log onto as admin because we have no Idea what the password is. Default credentials don't work and commands such as reset_config and reset_password-all when entered via console returns unknown command error. No idea what revision of software box is running.

Thanks

16 REPLIES
Cisco Employee

Help Required (Codian ISDN 3240)

Hi Irfan,

reset_password is the right command.

From the description, I see that you are using "reset_password-all".

Let me know if it works or not.

-Sagar

New Member

Help Required (Codian ISDN 3240)

Hi Sagar,

Thanks for the repsonse.

reset_password via console returns unknown command error message.

any further further help would be appreciated.

regards

Cisco Employee

Help Required (Codian ISDN 3240)

Hi Irfan,

type help on the prompt and it will display list of  commands.

Could you please paste the output?

-Sagar

New Member

Help Required (Codian ISDN 3240)

Hi Sagar,

once agaian thanks for the quick response, below is the output via console when typing ? or help

? : Display commands

        help : Display commands

        dhcp : Use DHCP

      static : Use static IP

        ping : Test network connectivity

   ethertype : Set ethernet link type

      reboot : Reboot

    shutdown : Cleanly shutdown

      status : Show network status

destination : Manipulate IP destinations

     service : Control access to IP services

  ip_control : Control enablement of interfaces

feature_key : Submit a feature key

ISDN-GW:> help

           ? : Display commands

        help : Display commands

        dhcp : Use DHCP

      static : Use static IP

        ping : Test network connectivity

   ethertype : Set ethernet link type

      reboot : Reboot

    shutdown : Cleanly shutdown

      status : Show network status

destination : Manipulate IP destinations

     service : Control access to IP services

  ip_control : Control enablement of interfaces

feature_key : Submit a feature key

ISDN-GW:> Looking for host 10.2.10.4 and service ntp

Cisco Employee

Help Required (Codian ISDN 3240)

Hi Irfan,

Its strange that I dont see reset-config option here. Give me a day and i shall be able to answer you.

As of now i don't have console access to my Lab gateway.

Also try this (not sure if this works)

-reboot the ISDN GW and execute reset_config within 30 secs once booting is completed.

-Sagar

Help Required (Codian ISDN 3240)

Hi Irfan,

If you have forgotten your password for your Cisco acquired TANDBERG/Codian product you need to restore the unit to its factory settings to reset it. This will remove all configuration, including password

To return your unit to its factory settings and reset the password:

  1. Connect a serial terminal to your unit's console port using the settings given on the back panel label.
  2. Reboot the unit and watch the output on the serial terminal. After a few seconds you will see the message 'Cisco TelePresence MCU 8510 4.2(0.36) (Build 6.17(0.36)) starting' or similar.
  3. Type reset_config and press Enter.
  4. Type yes or y and press Enter. The unit will now reboot again.
  5. When bootup is complete, type status on the serial terminal to see the IP address that the unit has acquired using DHCP. Alternatively, set a static IP address on port A using the static command.
  6. Connect to the web interface of the unit and log in using 'admin' and no password. A warning message on the web page banner will tell you that a product activation key is required.
  7. Go to Settings > Upgrade and enter the unit's activation keys. After the activation keys are applied, you will be able to use your unit again.

To change the password, go to Users.

Thanks

Alok

Cisco Employee

Help Required (Codian ISDN 3240)

HI,

   Did you managed to get this one fixed ?

   If not please let me know and I can send you in a separate e-mail la webex invite and do it together once you have a pc with internet access and console cable conected to the unit

Kind regards,

Cristian

Cisco Employee

Help Required (Codian ISDN 3240)

Hi Cris,

On my lab gateway, I am able to use commad reset_config. However When Irfan tries to use it, it returs with unknown command error.

Not sure if was different method on older firmawares

-Sagar

Cisco Employee

Help Required (Codian ISDN 3240)

HI guys.  Have a 3220 GW on 2.1(1.49), and did the following:

Watched on the console for the following message:

"Hit Ctrl+C in the next 5 seconds to prevent isdn_gw start"

Once you see this, type in (no matter if it starts to scroll: Stare at the keyboard and type it): reset_config < hit enter> y

System will come around on boot, and then look to see in the console session for:

ISDN-GW:> reset_config

and....."Warning: This action is not reversible. Are you sure you want to continue?081317.561 SYSTEM : Info : Unique id "connection_id" was written; new allocation is 200000

y"

At least this is where it was written to mine. 

Later on you may see:

"

081331.963 CONFIGURATION : Info : save operation 3656 (9203 bytes) took 25.679s

081331.964 CONFIGURATION : Info : Config file /fat/igw_cfg.bak preallocating

Waiting for configuration file to reset

Configuration reset"

Then it will go down for a restart.

Give this a shot and see if it works.  Once you see that first line, type that in and continue to do it no matter if it scrolls or not. 

Let us know the outcome.  Thanks.

VR

Patrick

New Member

Help Required (Codian ISDN 3240)

Many thanks for your help so far guys, but still no closer to logging on as admin. below is the output from the gw when performing the above steps recommended:

***** FILE SYSTEM WAS MODIFIED *****

hddstrap: product type 12

Hit Ctrl+C in the next 5 seconds to prevent ISDN GW start

^C# reset_config

rm: /fat/mcu_cfg.xml: No such file or directory

rm: /fat/mcu_cfg.bak: No such file or directory

Mar 29 15:11:01 reboot: rebooted by root

[1]   Terminated              reset_config

# syncing disks... done

rebooting

Cisco Employee

Help Required (Codian ISDN 3240)

Hi Irfan - Run this again if possible, but don't hit ctrl-c to break the boot.  Once you see that line, just stare at the keyboard and type it in and let us know.

So, don't break the boot if you can. 

Let us know. 

VR

Patrick

New Member

Help Required (Codian ISDN 3240)

Hi Patrick,

First, Thanks for the quick response, secondly i did as suggested and below is the output:

fsck: Cannot open `/etc/fstab': No such file or directory

fsck: Cannot open `/etc/fstab': No such file or directory

** /dev/rwd0d

** File system is clean; not checking

hddstrap: product type 12

Hit Ctrl+C in the next 5 seconds to prevent ISDN GW start

reset_config

RUNNING ISDN GW

cfev: driver loaded successfully - built at Dec  7 2004 12:46:29

Module loaded as ID 0

/dev/rmd0c: 64.0MB (131072 sectors) block size 8192, fragment size 1024

        using 4 cylinder groups of 16.00MB, 2048 blks, 3968 inodes.

super-block backups (for fsck -b #) at:

    32, 32800, 65568, 98336,

net.inet.ip.ifq.maxlen: 50 -> 500

net.inet.udp.checksum: 1 -> 0

ftrace_init done

sendbatch_init

pci_init()

New Member

Help Required (Codian ISDN 3240)

Hi Guys,

I could do with some further help, are there any other commands i can try whilst in ctrl and c mode.

Thanks guys

Cisco Employee

Help Required (Codian ISDN 3240)

HI Irfan,

   It looks like we'll have to look into few logs to try to understand what's happening here so kindly asked to open a TAC case to further troubleshoot.

    Please attach to the case the serial output of the unit whilke trying to reset the unit password.

Regards

Help Required (Codian ISDN 3240)

Its two major options.

There is something strange with your box

Guess thats covered with what Christian said.

There still might be a usability issue.

I dont know how I shall interpret your last output.

First you would have to boot up the MCU (which this is parts of the output) you do not need to

press ctrl-c or anything like that. In the first 30 sec after the system is rebooted and up and running

type in: reset_password

Did you do that?

Please remember to rate helpful responses and identify

Cisco Employee

Help Required (Codian ISDN 3240)

Agree,

I think we should look into the full serial log to have a better understanding of what's happening

Cristian

1224
Views
0
Helpful
16
Replies