Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

How register EX90 tc4.2.3 whit CUCM 7.1.5?

I try configure the EX90 with third-party SIP Device (Advance) but no yet register.

also configure in EX90

provisioning --> ExternalManager --> address: IP Publisher

SIP -- > Profile 1 -- > Extension@IP Publisher

DefaultTrasport: Auto

Type: Cisco

Proxy 1:  Manual  ---> IP Publisher

Authentication 1 --> LoginName: UserDigest  Passwrod: Digest Credentials

CUCM

Device Name: MAC EX90

DP, Location, CSS, Device Security Profile, SIP Profile, Digest User.

Line 1 Extension

Try with SIP Basic also but no register.

Everyone's tags (1)
1 ACCEPTED SOLUTION

Accepted Solutions
New Member

How register EX90 tc4.2.3 whit CUCM 7.1.5?

Hi,

  The units can be registered to cucm as third party (basic) endpoints.

Please find the steps to register.

Configure sip settings on unit such as sip uri and proxy address.

1.  Sip Mode: on

2.  SIP Uri:    DN@ipaddress of cucm   eg: 9011@10.10.10.1

3.  Discovery : manual

4.  proxy Address:  ip address of cucm.

5.  Type: standard

6.  Default Transport: let it be auto however incase that did not work, change to udp.

7.  TLs: off

8:  Sip authentication user name:  user you have created on cucm  eg  9011

9.  Password:  use same password configured while creating user  9011

10. Disable provisioning mode.

CUCM config:

1.  Select third party basic profile.

2.  add mac address of mxp endpoint.

3.  select proper sip profile, phone templates etc.

4.  under digest user and owner user id select the same user eg: 9011

5.  save the configuration and assign same DN that we used in sip uri settings on mxp.

6.  Also associate mxp device to user using device association pane on cucm.

Please let me know if these work for you. I have tried this in my lab and that works.

Thanks,

Amlesh

5 REPLIES
New Member

How register EX90 tc4.2.3 whit CUCM 7.1.5?

Hi,

  The units can be registered to cucm as third party (basic) endpoints.

Please find the steps to register.

Configure sip settings on unit such as sip uri and proxy address.

1.  Sip Mode: on

2.  SIP Uri:    DN@ipaddress of cucm   eg: 9011@10.10.10.1

3.  Discovery : manual

4.  proxy Address:  ip address of cucm.

5.  Type: standard

6.  Default Transport: let it be auto however incase that did not work, change to udp.

7.  TLs: off

8:  Sip authentication user name:  user you have created on cucm  eg  9011

9.  Password:  use same password configured while creating user  9011

10. Disable provisioning mode.

CUCM config:

1.  Select third party basic profile.

2.  add mac address of mxp endpoint.

3.  select proper sip profile, phone templates etc.

4.  under digest user and owner user id select the same user eg: 9011

5.  save the configuration and assign same DN that we used in sip uri settings on mxp.

6.  Also associate mxp device to user using device association pane on cucm.

Please let me know if these work for you. I have tried this in my lab and that works.

Thanks,

Amlesh

New Member

How register EX90 tc4.2.3 whit CUCM 7.1.5?

Amlesh Sengar Hi Thanks for you respond. Is right. The EX90 was registered with CUCM  also using third party Third-party SIP Device. Best regards.

New Member

How register EX90 tc4.2.3 whit CUCM 7.1.5?

Hi,

Please confirm if the EX90 is not registered to call manager with the configuration provided above.

Incase it does not registered.  please provide xstatus sip from API mode.

Also type command " log ctx sippacket debug 9", this will enable sip packets sent/received to EX90.

check the response received from CUCM.

Note: disable debug using command " log ctx sippacket debug off"

Thanks,

Amlesh

Green

How register EX90 tc4.2.3 whit CUCM 7.1.5?

as a recommendation you should be running TC5 and CUCM 8.6 to get a native functionality for TAA endpoints.

New Member

How register EX90 tc4.2.3 whit CUCM 7.1.5?

Hi Thanks for recommender You know  EX 90 support multi conference in the version TC 5 with CUCM 8.6. Best regards

2436
Views
0
Helpful
5
Replies
CreatePlease to create content