Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

How to swap the C90 from TC 7.0.2 to cmterm 7.0.2

Dear all,

 

We would like to register the C90 to CUCM 8.6, so we have downloaded the cmterm-s52000tc7_0_2.cop from cisco.com. 

Any knows how to swap the C90 codec from TC version to cmterm CUCM version?

 

Best Regards,

Ben LAi

  • TelePresence
Everyone's tags (1)
1 ACCEPTED SOLUTION

Accepted Solutions
Silver

Hi Ben cmterm-s52000tc_7_0_2

Hi Ben

 

cmterm-s52000tc_7_0_2 is just software image which can be used when upgrading version from CUCM.

You can register you C90 having TC 7.0.2 version on it.

create device profile on CUCM for C90 unit and assign DN to it.

endpoint SIP configure:

 

xConfiguration SIP Profile 1 URI: "directorynumber (8001 whatever you assign in CUCM)@10.121.74.121"
 xConfiguration SIP Profile 1 DefaultTransport: TCP
*c xConfiguration SIP Profile 1 TlsVerify: Off
*c xConfiguration SIP Profile 1 Type: Cisco
*c xConfiguration SIP Profile 1 Outbound: Off
*c xConfiguration SIP Profile 1 Proxy 1 Discovery: Manual
*c xConfiguration SIP Profile 1 Proxy 1 Address: IP address of CUCM.

this should work fine.

 

 

 

5 REPLIES
Silver

Hi Ben cmterm-s52000tc_7_0_2

Hi Ben

 

cmterm-s52000tc_7_0_2 is just software image which can be used when upgrading version from CUCM.

You can register you C90 having TC 7.0.2 version on it.

create device profile on CUCM for C90 unit and assign DN to it.

endpoint SIP configure:

 

xConfiguration SIP Profile 1 URI: "directorynumber (8001 whatever you assign in CUCM)@10.121.74.121"
 xConfiguration SIP Profile 1 DefaultTransport: TCP
*c xConfiguration SIP Profile 1 TlsVerify: Off
*c xConfiguration SIP Profile 1 Type: Cisco
*c xConfiguration SIP Profile 1 Outbound: Off
*c xConfiguration SIP Profile 1 Proxy 1 Discovery: Manual
*c xConfiguration SIP Profile 1 Proxy 1 Address: IP address of CUCM.

this should work fine.

 

 

 

New Member

Dear Amehla,I am much

Dear Amehla,

I am much appreciated on your kindly support.

Actually, we have tried to follow the administering_endpoints_running_tc5_on_cucm8-6 ( and tc6 on ucm 9.10. However, those guides did not mention the endpoint configuration as detail as your recommended SIP configuration.

There are two video endpoints registered to cucm for further testing, and really want to say a big thanks.

Best Regards,

Ben Lai

Cisco Employee

that is largely because those

that is largely because those settings are a mix of things that are done automatically, and things that depend on your deployment.  

The endpoint is provisioned through CUCM, you should be configuring the provisioning mode and settings... and the endpoint will be configured as part of it's config download from CUCM.

Silver

one more thing, for native

one more thing, for native registration, you should have CUCM 8.6.2 or higher.

Cisco Employee

Check out the "Cisco

Check out the "Cisco TelePresence Administering TC Endpoints on CUCM" guides on Cisco.com - they guide you through all the CUCM and Endpoint configuration steps that are necessary.

http://www.cisco.com/c/en/us/support/collaboration-endpoints/telepresence-integrator-c-series/products-maintenance-guides-list.html

 

 

70
Views
0
Helpful
5
Replies
This widget could not be displayed.