Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Simple Discussion : TMS CCC shows Point-To-Point ad hoc call?

Hi,

A point-to-point call is made by two Cisco C-series endpoints, without booking in TMS.

I was wondering if CCC shows Point-To-Point ad hoc call.

Assume that we are using TMS(14.3.1) and want to control the call through CCC(Conference Control Center). Although It is not booked in TMS.

Futher Deployment Information:

-C-series as enpoints

-TMS(14.3.1)

-VCS(7.2.1)

-Conductor(XC2.2, B2BUA)

-MCU(4.4)


  • TelePresence
2 ACCEPTED SOLUTIONS

Accepted Solutions
VIP Green

Simple Discussion : TMS CCC shows Point-To-Point ad hoc call?

Yes, ad-hoc calls will show in the Active conferences list in TMS Conferece Control Centre.  You can then see the details and control the conference similar to a booked one.

Wayne

--

Please remember to rate responses and to mark your question as answered if appropriate.

Re: Simple Discussion : TMS CCC shows Point-To-Point ad hoc call

Ticking that box will show calls made on the fly, whether you connect these from the end-point itself or in TMS makes no difference.

So, yes, if someone makes a call without it being booked in TMS, it will show up as an ad-hoc call.

/jens

Please rate replies and mark question(s) as "answered" if applicable.

Please rate replies and mark question(s) as "answered" if applicable.
7 REPLIES
VIP Green

Simple Discussion : TMS CCC shows Point-To-Point ad hoc call?

Yes, ad-hoc calls will show in the Active conferences list in TMS Conferece Control Centre.  You can then see the details and control the conference similar to a booked one.

Wayne

--

Please remember to rate responses and to mark your question as answered if appropriate.

New Member

Simple Discussion : TMS CCC shows Point-To-Point ad hoc call?

Thanks to your attempt reply, Wayne.

By the way, Did you put those deployment under your consideration?

Also with your conclusion, It turns out that the call signal flows through TMS even if It is not booked in TMS. is it right?

Simple Discussion : TMS CCC shows Point-To-Point ad hoc call?

Just make sure you tick the box

/jens

Please rate replies and mark question(s) as "answered" if applicable.

Please rate replies and mark question(s) as "answered" if applicable.
New Member

Simple Discussion : TMS CCC shows Point-To-Point ad hoc call?

Thanks, Jens.

Isn't it related to ad-boc booking? or related to both ad-hoc booking and ad-hoc without booking?

I just wanted to make sure of it.

Re: Simple Discussion : TMS CCC shows Point-To-Point ad hoc call

Ticking that box will show calls made on the fly, whether you connect these from the end-point itself or in TMS makes no difference.

So, yes, if someone makes a call without it being booked in TMS, it will show up as an ad-hoc call.

/jens

Please rate replies and mark question(s) as "answered" if applicable.

Please rate replies and mark question(s) as "answered" if applicable.
New Member

Simple Discussion : TMS CCC shows Point-To-Point ad hoc call?

Hey Ciscosters,

Now I got an Issue here..

I made a point-to-point call without booking in TMS, and couldn't find any active conference in TMS CCC.

Let's see.

There is no active one, but

went to the navigator and check endpoint's status, and they were in call.

Why this happens? oh..

New Member

Simple Discussion : TMS CCC shows Point-To-Point ad hoc call?

Problem resolved! I missconfigured the section for ad-hoc conference discovery in network setting below.

Thanks guys,

Paul

313
Views
0
Helpful
7
Replies