Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

CCM6 mgsp

Hi. I have ccm6.0 and 2821 gateway with vic2-4fxo interface card. I have configure mgcp on gateway and ccm.

My config.

_______________________

!

voice-card 0

no dspfarm

!

!

control-plane

!

!

!

voice-port 0/3/0

signal groundStart

timing hookflash-out 50

station-id number 225

caller-id enable

!

voice-port 0/3/1

signal groundStart

station-id number 225

caller-id enable type 1

!

voice-port 0/3/2

!

voice-port 0/3/3

!

voice-port 2/0/0

!

voice-port 2/0/1

!

voice-port 2/0/2

!

voice-port 2/0/3

!

voice-port 2/0/4

!

voice-port 2/0/5

!

voice-port 2/0/6

!

voice-port 2/0/7

!

voice-port 2/0/8

!

voice-port 2/0/9

!

voice-port 2/0/10

!

voice-port 2/0/11

!

voice-port 2/0/12

!

voice-port 2/0/13

!

ccm-manager mgcp

ccm-manager music-on-hold

ccm-manager config server 10.10.18.5

ccm-manager config

!

mgcp

mgcp call-agent 10.10.18.5 service-type mgcp

mgcp dtmf-relay voip codec all mode out-of-b

mgcp rtp unreachable timeout 1000 action not

mgcp modem passthrough voip mode nse

mgcp vad

mgcp voice-quality-stats all

mgcp package-capability rtp-package

mgcp package-capability sst-package

mgcp package-capability pre-package

no mgcp package-capability res-package

no mgcp package-capability fxr-package

no mgcp timer receive-rtcp

mgcp sdp simple

mgcp validate domain-name

mgcp validate call-agent source-ipaddr

mgcp endpoint offset

no mgcp explicit hookstate

mgcp rtp payload-type g726r16 static

!

mgcp profile default

!

!

!

dial-peer voice 999010 pots

!

dial-peer voice 999030 pots

service mgcpapp

port 0/3/0

!

dial-peer voice 1 pots

!

!

!

!

gatekeeper

shutdown_______________________

When i call on call manager over port 0/3/1 my call not come on ccm/ And when i call from ip phone over port 0/3/1 call not work.

Can i fix it?

1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

Re: CCM6 mgsp

where's the dial-peer for 0/3/1?

i only see the one for 0/3/0

if you don't have it, then add it to the config, do a no mgcp / mgcp and try again

did you verified the endpoint status in CUCM to be registered before the test? if it shows unregistered that's why it fails

HTH

javalenc

if this helps, please rate

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
1 REPLY
Cisco Employee

Re: CCM6 mgsp

where's the dial-peer for 0/3/1?

i only see the one for 0/3/0

if you don't have it, then add it to the config, do a no mgcp / mgcp and try again

did you verified the endpoint status in CUCM to be registered before the test? if it shows unregistered that's why it fails

HTH

javalenc

if this helps, please rate

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
170
Views
0
Helpful
1
Replies
CreatePlease to create content