Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

CUE problem

Hello,

      I am trying to install CUE on AIM cisco 3825. I did the initial configuration and when the device is reloading its stuck .. may its trying to reach my DNS server as I have given my dns details in initial setup. Please let me know how can i remove all the configurations and start it from the begining.

Thanks

Retrying install. LDAP objectClass.bdb is missing, system otherwise OK

Retrying install. LDAP objectClass.bdb is missing, system otherwise OK

Serial Number: FOC13503EUB

read workflow properties

finish setting sysdb callagent

INIT: Entering runlevel: 2

********** rc.post_install ****************

INIT: Switching to runlevel: 4

INIT: Sending processes the TERM signal

==> Starting CDP

STARTED: ntp_startup.sh

STARTED: LDAP_startup.sh

STARTED: SQL_startup.sh

STARTED: dwnldr_startup.sh

STARTED: HTTP_startup.sh

STARTED: probe

STARTED: fndn_udins_wrapper

STARTED: superthread_startup.sh

STARTED: ${ROOT}/usr/wfavvid/run

Waiting 282 ...

5 REPLIES
New Member

CUE problem

I am still waiting for some one to reply and just give me an idea ???

CUE problem

Does the CUE boot up properly?

Please rate replies and mark question as "answered" if applicable.

Please rate replies and mark question as "answered" if applicable.
New Member

CUE problem

here it what happens ...

Initializing memory.  Please wait. ... 256 MB SDRAM detected

BIOS Version: Cisco SE-AIM 01.02

BIOS Build date: 08/14/03

System Now Booting ...[BOOT-ASM]

Please enter '***' to change boot configuration:

Loading disk:/bzImage ... done.

Verifying ... done.

Starting Kernel.

Platform: aim

Using existing trace log

Cisco init

INIT: version 2.86 booting

mounting proc fs ...

mounting sys fs ...

mounting /dev/shm tmpfs ...

reiser root fs ...

Reiserfs super block in block 16 on 0x801 of format 3.6 with standard journal

Blocks (total/free): 248976/170123 by 4096 bytes

Filesystem is clean

Filesystem seems mounted read-only. Skipping journal replay.

Checking internal tree..finished

FILESYSTEM CLEAN

Remounting the root filesystem read-write...

kernel.sem = 1900 4000 32 100

vm.overcommit_memory = 1

                Welcome to Cisco Service Engine

Setting the system time from hardware clock

********** rc.aesop ****************

Populating resource values from /etc/aim_rsrc_file

Populating resource values from /etc/default_rsrc_file

Populating resource values from /etc/products/cue/default_rsrc_file

Populating resource values from /etc/products/cue/aim_rsrc_file

Processing manifests . . . . . . . . . . . . complete

==> Management interface is eth0

==> Management interface is eth0

Retrying install. LDAP objectClass.bdb is missing, system otherwise OK

Serial Number: FOC13503EUB

read workflow properties

finish setting sysdb callagent

INIT: Entering runlevel: 2

********** rc.post_install ****************

INIT: Switching to runlevel: 4

INIT: Sending processes the TERM signal

==> Starting CDP

STARTED: ntp_startup.sh

STARTED: LDAP_startup.sh

STARTED: SQL_startup.sh

STARTED: dwnldr_startup.sh

STARTED: HTTP_startup.sh

STARTED: probe

STARTED: fndn_udins_wrapper

STARTED: superthread_startup.sh

STARTED: ${ROOT}/usr/wfavvid/run

Waiting...1

Doesnt comes to the prompt

CUE problem

It seems that the OS is corrupted. I'd suggest you perform a restore.

Refer to this link:

http://www.cisco.com/en/US/docs/voice_ip_comm/unity_exp/rel3_0/installation/guide/upg3boot.pdf

Please rate replies and mark question as "answered" if applicable.

Please rate replies and mark question as "answered" if applicable.
New Member

CUE problem

Thanks for the support. I will keep the thread opened and see if some one else can keep more input on the issue.

287
Views
0
Helpful
5
Replies