Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

CUPC not able to connect to Presence

Hi there,

We used to use CUCM 6.x and CUPS 6.x butI've rebuilt our CUPS server as version 7, and we are now using CUCM 7.

I've got everything working apart from the Presence side of things, where the Presence client Server Health under the CUPC client is red, and not able to connect (Retrying). All other connections are green.

I can't see anything wrong on the CUPS server from the troubleshooter, and I have reviewd most/all of the CUPS posts on here regarding this issue.

Thing's i've done to try and resolve the issue:

- Applied an "ALL" incoming ACL

- Set the Proxy domain to "nowcomm.local"

- Reset everything

- Tried multiple PC's in the office to figure out if firewalls were causing the problem, but all have the same problem

When we ran CUPS 6.x everything seemed to work fine with these settings, so i'm a bit lost now as to what else I can try to do!

Any suggestions welcome. Thanks,

Mike.

19 REPLIES

Re: CUPC not able to connect to Presence

On your CUPS server and also your Pub/Sub, have you added in the correct DNS and domain name to the servers?

You can do this from CLI of each server:

Set network domain (enter domain name)

you will need to reboot the machines.

if this is not in here, typically, the SIP Publish trunk will not work on Pub/Sub correctly. And on CUPS, it can not resolve names correctly.

New Member

Re: CUPC not able to connect to Presence

Hmm yes I thought it might be something to do with it - we're not using DNS at all on any of the servers, and i've renamed the hostid's to be just IP addresses.

I'm not ruling this out, but it used to work with 6.x !

Re: CUPC not able to connect to Presence

Right.. it used to work with 6, but not with 7x I have found. I changed everything to IPs and it did not work for me. I opened a tac case, added in my DNS, and domain names to the pub/sub/cups and it started working.

Also, if you are trying to see yourself as presence, it does not work. If open up your client, add in your own name, this hoses the presence state completely.

New Member

Re: CUPC not able to connect to Presence

Good point, i'd best remove myself! Thanks for that one...

Just sorting the DNS details now, thanks for the input!

Re: CUPC not able to connect to Presence

I spent hours trying to figure out why my presence would not change. Finally I figured out or TAC, cant remember which, we removed my name from my own client and magically it started working. It's like it was looping itself for presence and never worked. So for testing, make sure you have (2) clients up and running to really test that it works. One client is not a good test.

Good luck!

Red

Re: CUPC not able to connect to Presence

What version is your CUPC? 1.2.x or 7.0.x?

Usually we see this behavior on different version of CUPC instead of CUPS.

Workflow has been changed on CUPC 7.0.x. It'll try to use the node_name+proxy_domain to connect to presence.

For more detailed information, please see:

http://htluo.blogspot.com/2009/01/how-does-cupc-deterine-presence-address.html

Michael

New Member

Re: CUPC not able to connect to Presence

Ok I'm using CUPC 7.x

I've added DNS records to our AD server, and then enabled the DNS servers on the CUCM Publisher (We dont have Subs), and on the CUPS server. I then rebooted both boxes.

I can successfully enter now-d-cups or now-d-cm-pub into my browser and it resolves correctly.

Presence still isnt working however. Thanks for your post Michael, I had a read of your blog. Below is the text from the Presence server health window:

Presence.Domain=nowcomm.local

Presence.MostRecentListenPort=50027

Presenc.Primary.Address=now-d-cups

Presence.Primary.Port=5060

Presence.Primary.Protocol=TCP

Presence.username=mgerrard

Users in the contacts list originally appear as aaboo@nowcomm.local before resolving to the proper display name.

Mike.

Red

Re: CUPC not able to connect to Presence

From your CUPC computer, can you ping now-d-cups.nowcomm.local? This is the address CUPC tried to connect.

Michael

New Member

Re: CUPC not able to connect to Presence

Hi Michael, yes I can no problems.

The plot thickens...

I found that under licensing, none of the units were being used! Some of the services under service parameters had "Inactive" next to them, but a quick visit to Serviceability told me that the services were activated and running (the troublshooter also says the same). i had to fully deactivate services one at a time, and reactivate them to get the services to go active properly, and to use the licenses from the pool. Definitely something screwy going on!

So..

I'm now able to see that Presence has gone "green" in the client's troubleshooter, but still no Presence information. One other slight oddity is that adding a user to the contacts list, doesn't appear until I close the program completely and re-enter it.

Mike.

Red

Re: CUPC not able to connect to Presence

This is called "Notification Issue". In English - "status didn't update until next logon".

Usually, it's firewall or VPN related. The best way to verify is to do sniffer capture on client and server side.

Michael

New Member

Re: CUPC not able to connect to Presence

No firewall involved - just inter-vlan routing.

Although all the services are now green, including presence, we still get no presence information in the CUP client :(

CSS, DNS, all check out ok.

Any more ideas anyone?

Red

Re: CUPC not able to connect to Presence

The idea already given :)

"The best way to verify is to do sniffer capture on client and server side".

That's the ultimate way to tell if it's network related or not. (and easiest way)

New Member

Re: CUPC not able to connect to Presence

I should be able to set this up today, and i'll post the results after i've had a look.

Have you any other suggestions though Michael? We're running inter Vlan routing (So no firewalls) and I have disabled all firewalls on my PC, including uninstalling VPN client. The thing is though that it used to work with CUPS 6.x with VPN client installed (Though my Windows firewall has always been disabled). The server has been rebuilt, but has the same IP address so routing etc to the box should be the same.

New Member

Re: CUPC not able to connect to Presence

I've had the same problems here and we went back to CUPS 6.0(4).

Cisco has released CUPS 7.0(3) yesterday but there is no Readme for it now on the Cisco Site but all other new documents.

Reg.

Johann

Red

Re: CUPC not able to connect to Presence

Even if you're not running Cisco VPN Client, the service is still running in background.

Stop the service to test CUPC just in case.

Michael

Re: CUPC not able to connect to Presence

Can you post a screen shot of your SIP Security profile and your SIP Trunk on CUCM?

Also did you enable the CUPS Service in CUCM Services from False to True?

New Member

Re: CUPC not able to connect to Presence

I'm with the same problem. The CUPC is not receiving the Presence IP Address from (?) the Presence Server (???).

I don't understand. I go to "Show Server Health" and the Presence is with an error: "None server configured".

Bronze

Re: CUPC not able to connect to Presence

Go to Application, CUPC, Proxy profile. Select the proxy/presence server. Make sure the user is associated there.

Please rate if this helped.

New Member

Re: CUPC not able to connect to Presence

Thanks!! You completely solve my problem!! Thank you very much.

631
Views
19
Helpful
19
Replies
CreatePlease login to create content