Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Login to CME as Administrator failed

I have:

Router 2851

CME version 7.1

Cisco Unity Express version (7.0.5)

The config:

--------------------

!
telephony-service
max-ephones 5
max-dn 10
ip source-address 10.10.230.1 port 2000
voicemail 3180
max-conferences 8 gain -6
web admin system name admin password lab
dn-webedit
time-webedit
transfer-system full-consult
transfer-pattern .T
create cnf-files version-stamp 7960 Apr 14 2010 21:31:39
!

!
interface Service-Engine1/0
ip unnumbered Vlan230
service-module ip address 10.10.230.2 255.255.255.0
service-module ip default-gateway 10.10.230.1
!       

ip route 10.10.230.2 255.255.255.255 Service-Engine1/0

!
ip http server
ip http authentication local
ip http path flash:

---------------------------

From the Cisco Unity Express Initiañization Wizard, it is neccesary to enter the Callmanager Express Login, but an error is receiver:

error1.JPG

In the router I can´t see the GUI file

Router#sh flash:

CompactFlash directory:
File  Length   Name/status
  1   46355244  c2800nm-ipvoice_ivs-mz.124-24.T3.bin 
  2   660      vlan.dat 
[46356032 bytes used, 17869244 available, 64225276 total]
62720K bytes of ATA CompactFlash (Read/Write)

I have the same problem. Do you know how fix it?

Regards

Ivan Rivas

Everyone's tags (1)
1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

Re: Login to CME as Administrator failed

Hi,

You can download the GUI files from this link according to the version you have:

http://tools.cisco.com/support/downloads/go/ImageList.x?relVer=7.1&mdfid=277641082&sftType=Unified+Communications+Manager+Express+Complete+Support+File+Set&optPlat=&nodecount=3&edesignator=null&modelName=Cisco+Unified+Communications+Manager+Express&t...

1. Download appropriate tar file to tftp server. cme-basic-x.x.x.tar ? contains basic CME

system files including GUI, MoH and phoneloads

cme-gui-x.x.x.tar ? contains basic CME GUI files only

2. Logon to privileged EXEC mode of router CLI

3. Enter archive command to extract contents of tar file to router Flash memory:
Router# archive tar /xtract tftp://ip-address/filename flash:

Example 1:

To extract contents of cme-basic-3.0.3.tar from tftp server 192.168.1.1 to flash:

archive tar /xtract tftp://192.168.1.1/cme-basic-3.0.3.tar flash:

Example 2:

To extract contents of cme-gui-3.0.3.tar from tftp server 192.168.1.1 to flash:

archive tar /xtract tftp://192.168.1.1/cme-gui-3.0.3.tar flash:

This will update all the gui files in the location which the gui checks on the flash.

Regards,

Tere

Regards, Tere. If you find this post helpful, please rate! :)
4 REPLIES
Cisco Employee

Re: Login to CME as Administrator failed

Hi Ivan,

You will need to upload the GUI files to the flash memory. Please refer to:

http://www.cisco.com/en/US/partner/products/sw/voicesw/ps4625/products_tech_note09186a0080aff515.shtml#error2

Regards,

Tere.

Regards, Tere. If you find this post helpful, please rate! :)
New Member

Re: Login to CME as Administrator failed

Thanks, What is the procedure for loading ? because in the document http://www.cisco.com/en/US/products/sw/voicesw/ps4625/products_tech_note09186a0080aff515.shtm

said: loading the GUI files to the GUI folder in flash

Thanks

Cisco Employee

Re: Login to CME as Administrator failed

Hi,

You can download the GUI files from this link according to the version you have:

http://tools.cisco.com/support/downloads/go/ImageList.x?relVer=7.1&mdfid=277641082&sftType=Unified+Communications+Manager+Express+Complete+Support+File+Set&optPlat=&nodecount=3&edesignator=null&modelName=Cisco+Unified+Communications+Manager+Express&t...

1. Download appropriate tar file to tftp server. cme-basic-x.x.x.tar ? contains basic CME

system files including GUI, MoH and phoneloads

cme-gui-x.x.x.tar ? contains basic CME GUI files only

2. Logon to privileged EXEC mode of router CLI

3. Enter archive command to extract contents of tar file to router Flash memory:
Router# archive tar /xtract tftp://ip-address/filename flash:

Example 1:

To extract contents of cme-basic-3.0.3.tar from tftp server 192.168.1.1 to flash:

archive tar /xtract tftp://192.168.1.1/cme-basic-3.0.3.tar flash:

Example 2:

To extract contents of cme-gui-3.0.3.tar from tftp server 192.168.1.1 to flash:

archive tar /xtract tftp://192.168.1.1/cme-gui-3.0.3.tar flash:

This will update all the gui files in the location which the gui checks on the flash.

Regards,

Tere

Regards, Tere. If you find this post helpful, please rate! :)
New Member

Re: Login to CME as Administrator failed

Great, Thanks

Now, the autentication is OK, The problem was the GUI files in the Flash,

The problem was fixed

Thanks again.

Ivan

2841
Views
5
Helpful
4
Replies