Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

MCS7825I4-K9 ethernet redundancy

The  MCS7825I4-K9 has 2 ethernet ports. Manuals are not clear on how to set these up in redundant mode. I have connected the second interface but that doesn't work. I can't find how to configure this.

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Red

MCS7825I4-K9 ethernet redundancy

Hi Evan,

Just to add a note to the info from Graham (+5)

"NIC Teaming for Network Fault Tolerance

The NIC teaming feature allows a  server to be connected to the Ethernet via two NICs and, therefore, two  cables. NIC teaming prevents network downtime by transferring the  workload from the failed port to the working port. NIC teaming cannot be  used for load balancing or increasing the interface speed.

Hewlett-Packard  server platforms with dual Ethernet network interface cards can support  NIC teaming for Network Fault Tolerance with Cisco Unified CM 5.0(1) or  later releases.

IBM server platforms with dual Ethernet network interface  cards can support NIC teaming for Network Fault Tolerance with Cisco  Unified CM 6.1(2) and later releases. "

And the command to do that as per  the CUCM OS CLI Reference Guide is:

"set network failover

This  command enables and disables Network Fault Tolerance on the Media  Convergence Server network interface card.

Command Syntax

failover  {enable | disable}

Parameters

enable enables Network Fault Tolerance.

disable  disables Network Fault Tolerance.

Requirements

Command privilege level: 1

Allowed  during upgrade: No "

The referenced guides:

SRND

http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/srnd/8x/callpros.html#wp1151635

CLI Ref

http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/cli_ref/7_1_2/cli_ref_712.html#wp40017

Cheers!
Rob

3 REPLIES
Silver

MCS7825I4-K9 ethernet redundancy

You need to say what you are trying to install and what version.

Some products support NIC teaming and some do not.

Graham

New Member

MCS7825I4-K9 ethernet redundancy

I'm installing CUCM 8.6.2

Hall of Fame Super Red

MCS7825I4-K9 ethernet redundancy

Hi Evan,

Just to add a note to the info from Graham (+5)

"NIC Teaming for Network Fault Tolerance

The NIC teaming feature allows a  server to be connected to the Ethernet via two NICs and, therefore, two  cables. NIC teaming prevents network downtime by transferring the  workload from the failed port to the working port. NIC teaming cannot be  used for load balancing or increasing the interface speed.

Hewlett-Packard  server platforms with dual Ethernet network interface cards can support  NIC teaming for Network Fault Tolerance with Cisco Unified CM 5.0(1) or  later releases.

IBM server platforms with dual Ethernet network interface  cards can support NIC teaming for Network Fault Tolerance with Cisco  Unified CM 6.1(2) and later releases. "

And the command to do that as per  the CUCM OS CLI Reference Guide is:

"set network failover

This  command enables and disables Network Fault Tolerance on the Media  Convergence Server network interface card.

Command Syntax

failover  {enable | disable}

Parameters

enable enables Network Fault Tolerance.

disable  disables Network Fault Tolerance.

Requirements

Command privilege level: 1

Allowed  during upgrade: No "

The referenced guides:

SRND

http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/srnd/8x/callpros.html#wp1151635

CLI Ref

http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/cli_ref/7_1_2/cli_ref_712.html#wp40017

Cheers!
Rob

476
Views
5
Helpful
3
Replies
CreatePlease to create content