Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

meet-me conference fail calling second number

Hello,

I have a Callmanager 6.1 single server. I have configured a range of DN for meet-me conference. The first conference meet-me it's ok (3 partecipants), but I can't open a second conference simultaneously.

Someone can help me?

12 REPLIES
Cisco Employee

Re: meet-me conference fail calling second number

you cannot press meet-me, dial another meet-me DN and use it??

or what are you exactly doing??

HTH

java

if this helps, please rate

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
New Member

Re: meet-me conference fail calling second number

If I press meet-me softkey on another ip-phone and dial another number of a meet-me DN range, the call fail.

This happens only if another conference meet-me is up.

Hall of Fame Super Red

Re: meet-me conference fail calling second number

Hi Lorenzo,

What number do you have configured at this setting?

Service Parameters Configuration >Clusterwide Parameters (Service)>Maximum MeetMe Conference

Here is some additional info;

Conference Bridge Configuration

http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_administration_guide_chapter09186a00801ecf8a.html

Adding a Meet-Me Number/Pattern

http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_administration_guide_chapter09186a00801ecf96.html#76011

http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note09186a008009476a.shtml#conference

Hope this helps!

Rob

New Member

Re: meet-me conference fail calling second number

Hi Rob,

I read the documents indicated.

The value at service parameters is "4" (default).

About meet-me DN, I have try in two manner:

one range 310X and two single DN 3150, 3151.

Both have the same problem.

One more info: the ip-phone use a cfb software in a MCS server in remote site, but

the device pool are the same. The link between the two locations is on MPLS (VPN). There are not cfb hardware, MRG or MRGL.

...The thing that I can not understand, it's that one conference runs but no two !...

Thanks

Lorenzo

New Member

Re: meet-me conference fail calling second number

check your media group list and make sure you have not somehow left out software bridge or have a hardware bridge with one allowed session

New Member

Re: meet-me conference fail calling second number

Hi,

I haven't media resource group list, media resource group or hardware conference bridge.

I have only the CFB software on any server of the cluster. One server has the cfb software in the same device pool of the ip-phone with the issue.

Lorenzo

New Member

Re: meet-me conference fail calling second number

curious. What do you mean with the ip phone with the issue. Are you trying to start 2 meetme conferences from the same phone?

New Member

Re: meet-me conference fail calling second number

No, I've tried with 2 ip-phones.

New Member

Re: meet-me conference fail calling second number

what do you get busy signal?

New Member

Re: meet-me conference fail calling second number

no, I get fast busy tone

New Member

Re: meet-me conference fail calling second number

try restarting conference bridge

Cisco Employee

Re: meet-me conference fail calling second number

you'll need to get a CUCM trace to find out what's going on if restarting the IPVMS service doesn't do the trick

HTH

java

if this helps, please rate

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
261
Views
0
Helpful
12
Replies
CreatePlease to create content