Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Attention: The Cisco Support Community site will be in read only mode on Dec14, 2017 from 12:01am PST to 11:30am for standard maintenance. Sorry for the inconvenience.

New Member

Meet-me

I need to configure the password to meet-me conference?

Someone how can i do it?

3 ACCEPTED SOLUTIONS

Accepted Solutions
Cisco Employee

Re: Meet-me

meet-me does not provide passwords

anyone that can dial the number can join if it has been initiated.

you can try to join thru unity with the supervised transfer + announcement to determine if you accept or deny access

applies to all versions and flavors

HTH

javalenc

if this helps, please rate

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
New Member

Re: Meet-me

Sorry for the delay. I've been swamped with some stuff. Here are the instructions of how it got it to work.

Regards,

Create a call handler for each of your Meet Me extension with the following settings:

Prifle Settings.

Owner ==> Subscriber (This would be your preference. Perhaps Help Desk, or general mailbox for conference bridges)

Extension ==> Meet Me extension.

Call Transfer Settings.

Transfer incoming calls to a phone?

Yes, ring this extension ==> Meet Me extension.

Transfer Type:

Supervise Transfer.

Rings to wait for: 2

If the number is busy ==> No holding.

Gather caller information:

Check,

Confirm (call can be accepted or dinied)

Ask Caller's name.

Messages Settings.

Message recipient: A selected subscriber. (owner of the call handler)

New Member

Re: Meet-me

It is not possible to password protect a meet me conference.

17 REPLIES
Cisco Employee

Re: Meet-me

meet-me does not provide passwords

anyone that can dial the number can join if it has been initiated.

you can try to join thru unity with the supervised transfer + announcement to determine if you accept or deny access

applies to all versions and flavors

HTH

javalenc

if this helps, please rate

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
Silver

Re: Meet-me

I have this doc on getting meetme to work through Unity but can not get it to work. I know it should work but something is missing. Please look it over. I got it here too.

rlp.

VIP Super Bronze

Re: Meet-me

Hi,

I wrote this document. What exactly is the problem you are having

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
New Member

Re: Meet-me

I had found a detailed document that went through setting up Unity to do the supervised transfer + announce several years ago and can not locate it again.

Does anyone have a link to that document?

Thanks,

Brian

Silver

Re: Meet-me

If anyone has it, I would like it too.

Randy

New Member

Re: Meet-me

I have implemented the supervised transfer through Unity through instructions found int he forum (transfer to meet me). Let me revise it tomorrow at the office before I post it.

regards

New Member

Re: Meet-me

hi ,any update?

New Member

Re: Meet-me

Sorry for the delay. I've been swamped with some stuff. Here are the instructions of how it got it to work.

Regards,

Create a call handler for each of your Meet Me extension with the following settings:

Prifle Settings.

Owner ==> Subscriber (This would be your preference. Perhaps Help Desk, or general mailbox for conference bridges)

Extension ==> Meet Me extension.

Call Transfer Settings.

Transfer incoming calls to a phone?

Yes, ring this extension ==> Meet Me extension.

Transfer Type:

Supervise Transfer.

Rings to wait for: 2

If the number is busy ==> No holding.

Gather caller information:

Check,

Confirm (call can be accepted or dinied)

Ask Caller's name.

Messages Settings.

Message recipient: A selected subscriber. (owner of the call handler)

Silver

Re: Meet-me

these are the Unity settings, what about ccm?

cti route point? but you can not give the cti route point the same extension as the meetme bridge number.

translation pattern?

Help!!!!!!!!!!

Randy

New Member

Re: Meet-me

Hi

Do you know how to put password to meet me?

New Member

Re: Meet-me

It is not possible to password protect a meet me conference.

Re: Meet-me

Hi -

You can check out two Cisco applications, MeetingPlace and MeetingPlace Express. Both products allow meetings to be scheduled using meeting passwords.

Ginger

Silver

Re: Meet-me

Ginger, thanks but do not want to have another server and program.

We are just looking for a way to have a way for Unity to dial the meetme bridge number. That way a subsriber can call the call handler and Unity will dial it so a phone user can be remote and doesn't have to be local to the phone soft key.

someone in this conversation sent his setting but only the Unity side. I need the ccm side too.

Randy

Cisco Employee

Re: Meet-me

on CCM side just make sure the VM port can reach the meet-me DN, nothing else. it's the same as if you wanted to reach a phone

HTH

java

if this helps, please rate

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
New Member

Meet-me

Hi,

The above requirement of starting the MeetMe conference through an external phone(PSTN) along with authentication,limit of users per conference and scheduleing feature IS POSSIBLE through an application and we have done it.

New Member

Meet-me

Hello,

The unity can create the meet-me conference in the CUCM?. or the inviter need to hang up, then push button meet-me in his phone and create the conference room?.

if the inviter need to create the conference room is mean that anyone that know the conference room can dial directly without use the unity control security. right?.

Cisco Employee

Meet-me

No, Unity cannot start the meetme.

Yes, assuming your CSS allows you to reach the meet-me DN directly, after the meeting is started you can join directly.

HTH

java

If this helps, please rate

www.cisco.com/go/pdihelpdesk

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
1728
Views
8
Helpful
17
Replies
CreatePlease to create content