Resolved! Connect Fex 2208 to 6120 FI
Hi All,Is it possible to connect a chassis with the 2208 IO modules to a UCS system with 6120 Fabric interconnects? if its possible, would we need to upgrade the firmware to UCSM 2.x ?ThanksKassim
Hi All,Is it possible to connect a chassis with the 2208 IO modules to a UCS system with 6120 Fabric interconnects? if its possible, would we need to upgrade the firmware to UCSM 2.x ?ThanksKassim
I'm trying to make a solution where the Fabric Interconnect will handle direct link with the storages but i don't know how to do it on the new FI 6200 series. For instance I can make the FC expansion module in 6100 series to switch and leave the fixe...
Hi,I have x2 UCS chassis spilt over 2 sites with x1 vsphere 5 cluster the VSM works on site A and site B doesnt load the VEM. The config is the same on the UCS/Fabric Interconnects/Nexus 5020. The x4 esxi hosts with the issue can still route vm/vmker...
Hi All,I have a question in regards to ISCSI boot via an appliance port on a Cisco UCS 6248 fi. The set up currently consists of a NetApp filer (FAS3240) with a direct connection to the FI via an appliance port. The finalised setup will be eventually...
I'm curious if anyone has a guide or documentation on best practices for configuring a Hyper-V host and cluster on UCS. I see the Exchange/Hyper-V/UCS guide, but it really skips over my core question of how this is accomplished with only 2 vNICs. A H...
The Customer asked me to Quote UCS to Install Active Directory and Wins and other applications Could you pls advise which UCS series I should Recommend ? I don't have any experience about the UCS
For compatibility with older legacy software, i would like to know this (assuming Microsoft Extended Support contract until 2015)regards,Geert
Here's what we have:- two Blades M250- two fabric interconnets- one nexus 5000We have created two Service Profiles and assign to each blades. ESX 4.1 is already installed on both blades.The probelm is we can't ping to both ESX server concurrently. We...
Hi,We have a Dell Compellent SAN storage with iSCSI and FCoE module in pre-production environment.It is connected to new Cisco UCS infrastructure (5108 Chassis with 2208IOM + B200 M2 Blades + 6248 Fabric Interconnect) via 10G iSCSI module (FCoE modul...
Hi, all:I'm a newbie using UCS 2.0(1.x) and would like to reset multiple servers in a single command instead that doing one by one? Regards,Alberto.
I am planning the upgrade for our 6120XP FIs to be replaced with 6248s. I have the read the upgrade guide and need a little clarification. In our 6120s we are utilizing the N10-E0060 FC expansion slot for storage connectivity. We are not utilizin...
we are looking driver for " cisco alpine scsi enclosure device "Our enviroment are : C460 M2 Windows server 2003 X64 Enterprise edition R2 SP2 LSI CONTROLLER 9260-8iBest regards
Hi this might be an easy one but doing my head in.Do the ports on the 5596up (all 48) come fully licensed?We're looking at installing the following modules into the above N2K-C2232PP and N2K-C2248TP.What we need to figure out is basic licensing for t...
Hi Experts,We have IBM TotalStorage SAN16B-2 SAN Switch, & cisco UCS 6120 Fabric Interconnect, dint find any document for compatibilty between this.This is a SAN switch with each port capable of delivering a throughput of up to 4 gbps.Can we use this...
Just received 6 new UCS C210-M2s, four of them are perfect but having problems with two of them; All of the servers came with the RAID arrays built, one around 135GB and the other around 985GB. After installing vSphere 4.1 U2 on one of the servers, ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-26-2024 05:23 PM | ||
04-23-2024 12:18 AM | ||
04-16-2024 02:26 AM | ||
04-04-2024 11:22 AM | ||
03-18-2024 06:52 AM |