Hi, Anyone knows if there is any way to enable TACACS+ authentication for the cisco CIMC? we have many APICS server with CIMC but theres only the option to configure AD auth. Thanks in advance
Forum Posts
Resolved! WWPN not showing on NPV flogi-table
I have an environment with two FI 6248, two UCS 5108 and two 6510 brocade switches for san. UCSM has 4.0.4m version and FI are in "end host mode". We have two service profiles in use (PRD_1 & and PRD_2), both created from the same template (PRD_TE...
Resolved! UCS FC Port-Channel with Broade SAN SW
Hi All Can UCS FI(6454) end host mode use FC port to connect to Broade SAN SW(ds-6520b) and do port channels on both sides?
Need to replace a CPU on a UCS C240 M4 server as per https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c/hw/C240M4/install/C240M4/replace.html#45480. However, the CPU that was delivered doesn't have the CPU plastic frame. So I'm not able to...
What is the recommended level of separation when one client has two physically separate UCSX setups in two sites. One site is already setup, and we're about to start the deployment for the second site. We can define a new organization, resource group...
I have a physical Windows 2022 server with one NIC connected to FI-A and another to FI-B. What is the best practice to setup NIC teaming? From Cisco doc,UCS B-Series/C-Series/S-Series/HyperFlex-Series Teaming, Bonding Options with the Cisco VIC Card ...
Resolved! Can my FIs support : UCSB-EX-M4-1
Hi,I'm having 5 blades on older UCSM and I want to move it to a newer UCSM/FI1st question:According to my UCSM/FI version [screenshot attached], can I move this kind of server to it :UCSB-EX-M4-12nd questions (** update : it's the most important ques...
Resolved! SKU for VMware license
Dear Team Please advise what Cisco SKU for VMware license replacing below SKU VMW-VSP-STD-3A= Thanks in advance
Hi,We have existing running Hyperflex cluster with HX version 4.0.2c and vCenter/ESXi hosts 6.7 U3. Hyperflex cluster has DNS suffix that is domain XXXX.com and ESXi hosts name is esx1.XXXX.com, esx2.XXXX.com and so on.Can we change the name of the ...
Resolved! About SAN topology
Hi All, I have two questions:I have two FI-6454, each with two FC uplinks,1. As far as I know, a vHBA of a UCS Blade map to an FC uplink?2. If I want to setup the current two FC Uplinks into port channels, will it cause a disconnection? Thanks.
Resolved! VIC 1340
Hi Team,I have a blade B480 M5 with 6146 CPU , I am planning to install redhat 8.9 which is supported starting from 4.2(3) but looks like the CNA Adapter does not support on 4.2(3) for this matrix but 5.0(1) is supporting this 1340. Is there any issu...
Greetings, thanks for reading. I have NetApp storage attached to Nexus 5k for the FCoE zoning and SAN boot and then to ACI.We simply removed those connections to the 5k and instead directly attached to the Fabric Interconnects and went from twinax to...
Howdy Folks, Can anyone confirm if the UCS-FI-6454 can support a copper 10GBASE-T SFP+ module, specifically the SFP-10G-T-X? So far, all I've check the optics compatibility matrix and the 6400 spec-sheet and I see no mention of this module being supp...
If I modify the Firmware Policy with an incorrect version of firmware and it generates pending activities for hosts to get that on next reboot. But I don't want them to get that firmware version. Do I just go into pending activities and cancel them...
Summary:Can ssh into user-2 admin account using password ssh (or via the Web UI)can not use publickey with ssh, always prompts for passwordUser Guide for C-Series doesn't specify any requirements for public key type/bits that i can findI have ssh ena...
