04-05-2018 07:12 AM - edited 03-01-2019 01:30 PM
I'm having some trouble getting the HA to come online for our cluster. I'd assume it would come online on it's own but it doesn't seem to be.
Not sure what direction to take this or what information to provide.
Solved! Go to Solution.
04-05-2018 08:23 AM
As suspected, until you attach chassis or rack servers to the FI, you will not be in HA READY. This is expected. Please report back if issue persist after installing chassis.
04-05-2018 07:15 AM
Can you provide the outputs from UCS CLI:
UCS#show cluster extended-state
UCS#show pmon state
If you have not attached any chassis to your 6332, HA will not become ready, as it needs to have a heartbeat over the L1-L2 links between the switches, as well as a heartbeat down through the chassis from FI-A > IOM-A > IOM-B > FI-B
04-05-2018 08:22 AM
FI-A-A# show cluster extended-state
Cluster Id: 0xb26cc794383f11e8-0xbce770695a4e8d7d
Start time: Wed Apr 4 19:42:57 2018
Last election time: Wed Apr 4 20:04:00 2018
A: UP, PRIMARY
B: UP, SUBORDINATE
A: memb state UP, lead state PRIMARY, mgmt services state: UP
B: memb state UP, lead state SUBORDINATE, mgmt services state: UP
heartbeat state PRIMARY_OK
INTERNAL NETWORK INTERFACES:
eth1, UP
eth2, UP
HA NOT READY
No device connected to this Fabric Interconnect
FI-A-A(local-mgmt)# show pmon state
SERVICE NAME STATE RETRY(MAX) EXITCODE SIGNAL CORE
------------ ----- ---------- -------- ------ ----
svc_sam_controller running 0(4) 0 0 no
svc_sam_dme running 0(4) 0 0 no
svc_sam_dcosAG running 0(4) 0 0 no
svc_sam_bladeAG running 0(4) 0 0 no
svc_sam_portAG running 0(4) 0 0 no
svc_sam_statsAG running 0(4) 0 0 no
svc_sam_hostagentAG running 0(4) 0 0 no
svc_sam_nicAG running 0(4) 0 0 no
svc_sam_licenseAG running 0(4) 0 0 no
svc_sam_extvmmAG running 0(4) 0 0 no
httpd.sh running 0(4) 0 0 no
httpd_cimc.sh running 0(4) 0 0 no
svc_sam_sessionmgrAG running 0(4) 0 0 no
svc_sam_pamProxy running 0(4) 0 0 no
dhcpd running 0(4) 0 0 no
sam_core_mon running 0(4) 0 0 no
svc_sam_rsdAG running 0(4) 0 0 no
svc_sam_svcmonAG running 0(4) 0 0 no
04-05-2018 08:23 AM
As suspected, until you attach chassis or rack servers to the FI, you will not be in HA READY. This is expected. Please report back if issue persist after installing chassis.
04-05-2018 10:10 AM
04-05-2018 10:26 AM
Hello,
The L1-L2 should be directly connected to each other. L1 - L1 : L2-L2.
There should be no switch in between and ideally no patch panel either.
HTH,
Wes
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: