Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Which GLC-T 1 Gb adapters are approved for the XP6120 FI?

                   I have 4 GLC-T SFPs of various models. For some reason 2 of them does not work. IS not recognised by the FI. I have tried moving them around to other ports, and making sure I only use port 1 to 8 doing so. Are they faulty or should I get a specific GLT-C model?

SFP 1: 30-1410-02

SFP 2: 30-1410-03

The 2 other working SFPs I do not have the part numbers here.

Everyone's tags (7)
2 ACCEPTED SOLUTIONS

Accepted Solutions
Cisco Employee

Which GLC-T 1 Gb adapters are approved for the XP6120 FI?

Hi,

Do you have the port speed configured as 1gb or 10gb in ucsm?

Cisco Employee

Which GLC-T 1 Gb adapters are approved for the XP6120 FI?

Hello,

From "show int eth x/y " , the show interface speed is 10G instead of 1G.

Can you change it to 1G and verify the outcome ?

Padma

6 REPLIES
Cisco Employee

Which GLC-T 1 Gb adapters are approved for the XP6120 FI?

Hello,

Supported GLC-T models are listed here

http://www.cisco.com/en/US/prod/collateral/ps10265/ps10276/data_sheet_c78-524724.html

If you could connect those faulty SFP modules to FI, please execute the following commands and share the output

connect nxos

show interface eth X/Y transceiver details

Padma

New Member

Which GLC-T 1 Gb adapters are approved for the XP6120 FI?

FI6120XP-B(nxos)# show interface eth 1/5 transceiver details

Ethernet1/5

    transceiver is present

    type is 1000base-T

    name is CISCO-AVAGO

    part number is ABCU-5710RZ-CS2

    revision is

    serial number is AGM124227QP

    nominal bitrate is 1300 MBit/sec

    Link length supported for copper is 100 m

    cisco id is --

    cisco extended id number is 4

   Transceiver calibration is invalid

FI6120XP-B(nxos)# show interface eth 1/7 transceiver details

Ethernet1/7

    transceiver is present

    type is 1000base-T

    name is CISCO-METHODE

    part number is SP7041_Rev_F

    revision is F

    serial number is 00000MTC145004L4

    nominal bitrate is 1300 MBit/sec

    Link length supported for copper is 100 m

    cisco id is --

    cisco extended id number is 4

   Transceiver calibration is invalid

and this interface output:

FI6120XP-B(nxos)# show interface eth 1/5

Ethernet1/5 is down (SFP validation failed)

  Hardware: 1000/10000 Ethernet, address: 000d.ecfb.ae0c (bia 000d.ecfb.ae0c)

  Description: U: Uplink

  MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,

     reliability 255/255, txload 1/255, rxload 1/255

  Encapsulation ARPA

  Port mode is trunk

  auto-duplex, 10 Gb/s, media type is 10G

  Beacon is turned off

  Input flow-control is off, output flow-control is off

  Rate mode is dedicated

  Switchport monitor is off

  EtherType is 0x8100

  Last link flapped never

  Last clearing of "show interface" counters never

  30 seconds input rate 0 bits/sec, 0 bytes/sec, 0 packets/sec

  30 seconds output rate 0 bits/sec, 0 bytes/sec, 0 packets/sec

  Load-Interval #2: 5 minute (300 seconds)

    input rate 0 bps, 0 pps; output rate 0 bps, 0 pps

  RX

    0 unicast packets  0 multicast packets  0 broadcast packets

    0 input packets  0 bytes

    0 jumbo packets  0 storm suppression packets

0 giants      0 input error  0 short frame  0 overrun   0 underrun      0 watchd

og  0 if down drop

    0 input with dribble  0 input discard

    0 Rx pause

  TX

    0 unicast packets  0 multicast packets  0 broadcast packets

    0 output packets  0 bytes

    0 jumbo packets

    0 output errors  0 collision  0 deferred  0 late collision

    0 lost carrier  0 no carrier  0 babble

    0 Tx pause

  0 interface resets

FI6120XP-B(nxos)# show interface eth 1/7

Ethernet1/7 is down (Administratively down)

  Hardware: 1000/10000 Ethernet, address: 000d.ecfb.ae0e (bia 000d.ecfb.ae0e)

  MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,

     reliability 255/255, txload 1/255, rxload 1/255

  Encapsulation ARPA

  Port mode is access

  auto-duplex, 10 Gb/s, media type is 10G

  Beacon is turned off

  Input flow-control is off, output flow-control is off

  Rate mode is dedicated

  Switchport monitor is off

  EtherType is 0x8100

  Last link flapped never

  Last clearing of "show interface" counters never

  30 seconds input rate 0 bits/sec, 0 bytes/sec, 0 packets/sec

  30 seconds output rate 0 bits/sec, 0 bytes/sec, 0 packets/sec

  Load-Interval #2: 5 minute (300 seconds)

    input rate 0 bps, 0 pps; output rate 0 bps, 0 pps

  RX

    0 unicast packets  0 multicast packets  0 broadcast packets

    0 input packets  0 bytes

    0 jumbo packets  0 storm suppression packets

0 giants      0 input error  0 short frame  0 overrun   0 underrun      0 watchd

og  0 if down drop

    0 input with dribble  0 input discard

    0 Rx pause

  TX

    0 unicast packets  0 multicast packets  0 broadcast packets

    0 output packets  0 bytes

    0 jumbo packets

    0 output errors  0 collision  0 deferred  0 late collision

    0 lost carrier  0 no carrier  0 babble

    0 Tx pause

  0 interface resets

But regarding "the transceiver calibration invalid" status, I get the same output for my etherchannel in linked state:

FI6120XP-A(nxos)# show interface eth1/1 transceiver details

Ethernet1/1

    transceiver is present

    type is 1000base-T

    name is CISCO-METHODE

    part number is SP7041

    revision is E

    serial number is 00000MTC1250008A

    nominal bitrate is 1300 MBit/sec

    Link length supported for copper is 100 m

    cisco id is --

    cisco extended id number is 4

   Transceiver calibration is invalid

FI6120XP-A(nxos)# show interface eth1/2 transceiver details

Ethernet1/2

    transceiver is present

    type is 1000base-T

    name is CISCO-METHODE

    part number is SP7041_Rev_F

    revision is F

    serial number is 00000MTC145004BK

    nominal bitrate is 1300 MBit/sec

    Link length supported for copper is 100 m

    cisco id is --

    cisco extended id number is 4

   Transceiver calibration is invalid

Cisco Employee

Which GLC-T 1 Gb adapters are approved for the XP6120 FI?

Hi,

Do you have the port speed configured as 1gb or 10gb in ucsm?

Cisco Employee

Which GLC-T 1 Gb adapters are approved for the XP6120 FI?

Hello,

From "show int eth x/y " , the show interface speed is 10G instead of 1G.

Can you change it to 1G and verify the outcome ?

Padma

New Member

Which GLC-T 1 Gb adapters are approved for the XP6120 FI?

I will do this when I in the lab again, I don't know when. I forgot to change the port speed this time. Maybe the SFPs were not firmly connected the first time. I will report back in due course. Thanks all.

New Member

Which GLC-T 1 Gb adapters are approved for the XP6120 FI?

yes, it was wrong speed set. Now it has a link up. Thanks..

2418
Views
5
Helpful
6
Replies