About tdotvix1982

tdotvix1982 · 09-18-2012

My question pertains to using either BGP or HSRP at both the internet edge module and or WAN edge module for failover. I CANNOT realistically think of a situation where I would failover between two devices using HSRP at both the internet edge and WAN...

tdotvix1982 · 07-04-2012

Hi,I am faced with a challenge with a setup which was previously running in a flat network without a firewall. They had a proxy server running which did NATTING for them on the WAN interface whereas the LAN segment was plugged into the LAN interface....

tdotvix1982 · 06-11-2012

Hi,I am trying to create an IPSEC remote access vpn and am working for the first time with Network Object NAT on a 5512 X architecture with 8.6 OS. I would like to know how to create a NONAT scenario with users on the other side using a NAT 0 nat ent...

tdotvix1982 · 05-27-2012

Hi,We are recieving two separate last mile fibers from our ISP. We are receving two separate /30 subnets from the ISP and a separate /28 pool. Now the first pool for instance is x.x.x.128/30, the second one is x.x.x.136/30 and the last pool is x.x...

tdotvix1982 · 04-23-2012

Hi,I went through the configuration guide for 4500 series switches for NSF/SSO for failover between Sup's. I just wanted to know that that are we supposed to run the SSO command on both of the supervisors? Secondly, are we only supposed to run the ns...

tdotvix1982 · 07-05-2012

Hi Marcin,Thanks for your reply in this regard. The WCCP Server protocol requires a service running the WCCP client protocol at the proxy/client end. The router/ASA running WCCP would forward requests that match the WCCP ACL to the Cisco Cache Engine...

tdotvix1982 · 06-03-2012

Hi,Yes, but that wouldn't be the best design scenario now would it? It would create a double NAT scenario with NAT being configured on the firewall and the Internet Edge router. Also, it would defeat the main purpose of obtaining a /28 pool from the ...

tdotvix1982 · 06-02-2012

Hi,Well, after further investigations with the client and their ISP. I have learnt that the two /30 pools were for running eBGP with the ISP. The links were configured for failover using the Local Preference attribute. The other /28 pool was not assi...

tdotvix1982 · 04-24-2012

Oh great and what about the following commands:Non-Stop Forwarding:Switch(config)# router eigrp as-numberSwitch(config-router)# nsfDo we neet to apply them on other routers in the domain to make them NSF aware as well so that when they receive the ne...

tdotvix1982 · 04-23-2012

Very true indeed sir! Thank you for your valuable insight into the matter. Thanks for pointing the design flaw out. I meant to say Distribution to Core. Cheers.

Member Since	‎10-30-2005 05:47 PM
Date Last Visited	‎08-18-2017 03:55 AM
Posts	34
Total Helpful Votes Received	5

User Statistics

User Activity

RE: Failover using HSRP or BGP. Which is most suited on edge devices?

RE: USING A PROXY SERVER WITH AN ASA

NAT 0 using Network Object NAT in OS 8.6

LIVE IP on server behind DMZ zone scenario with BGP Failover Scenario

Requirement for NSF/SSO commands on standby or active supervisor on 4500

RE: USING A PROXY SERVER WITH AN ASA

LIVE IP on server behind DMZ zone scenario with BGP Failover Sce

LIVE IP on server behind DMZ zone scenario with BGP Failover Sce

Requirement for NSF/SSO commands on standby or active supervisor

RE: Doubt regarding Etherchannel terminating on different line c