About Steph1963

Steph1963 · 12-23-2015

Hi, I would like to know how we can validate the Commited Burst Size (Bc) that is applied to a Policy on Cisco IOS with an Ixia/Spirent Test set. Cisco documentation seems to indicate that bc=CIR/32 by default. What is the relation between the bu...

Steph1963 · 10-29-2015

Hello, I would like to know the signification of the following statistics in the the show ip cef X.X.X.X internal command traffic share X tmsstats: external/internal and the meaning of Load distribution: 0 1 0 1 0 1 0 1 0 1 1 1 1 1 1 (refcount...

Steph1963 · 03-25-2015

Hello,I would like to know if is possible to configure a CSRV 1000V (IOS XE) as a VPLS hub with two Cisco 7200 or 7600 router as shown in the attachement. Not being very familiar with VPLS, I would like to know if any of the two configurations would ...

Steph1963 · 03-18-2015

Hi Cisco Expert, I have seen on many Cisco Campus design document the Layer 3 Access to the Distribution Model as shown in figure 6 in the following linkhttp://www.cisco.com/en/US/docs/solutions/Enterprise/Campus/HA_recovery_DG/campusRecovery.html Th...

Steph1963 · 01-04-2014

Hi,I cannot connect make any PPP connection to a Cisco 2600 Aux port with Windows 7 or Vista. Is there anybody who would know how to establish a PPP connection to an aux port using Linux PPPD.Here is my 2600 configuration:username cisco password cisc...

Steph1963 · 03-25-2015

Hi Jon,This makes perfect sense, HSRP or GLBP would required a layer 2 link between the access switch and the distribution swithc. A layer 3 link between the access switch and the distribution switch would mean that the access route would route so HS...

Steph1963 · 03-24-2015

Hi Jon, Your explanation makes a lof of sense, now I underdand why it is not possible to have L3 between the access and distribution switches. Notice that with a L3 interconnect between the distribution pair and L2 to the access layer switches even t...

Steph1963 · 03-23-2015

Hi Jon, Many thanks for your help. I think that I have finally understand what you were trying to explain me. Running a Layer 3 between the distribution and the access prevents us of runnning HSRP or GLBP simply because you cannot have the same IP su...

Steph1963 · 03-19-2015

Hi John, Thanks for your quick reply,Sorry if I was not clear enough, I was not saying that only one instance of HSRP should run on the distribution switches but did not understand how HSRP was configured on Layer 2 Access with Layer 3 Distribution C...

Steph1963 · 11-21-2013

Hi Seb, Thanks for the correction.Based on some Cisco example that I have found, I thought it was possilbe bo used tunnel endpoints in different IPv6 subnet as long as a route to the IPv4 was available as shown in the attached link.http://ardenpackee...

Member Since	‎05-10-2010 07:21 AM
Date Last Visited	‎08-18-2017 04:00 AM
Posts	177

User Statistics

User Activity

How to test Commited Burst size (Bc) with an Ethernet Test Set

show ip cef X.X.X.X internal statistics

Hub and Spoke VPLS between Cisco CSR 1000v (Hub) and 7200 or 7600 (Spoke)

High Availability Campus Design: Layer 3 Access to the Distribution

Linux PPPD command to establish a PPP conection with Aux Port

Hi Jon,This makes perfect

Hi Jon, Your explanation

Hi Jon, Many thanks for your

Hi John, Thanks for your

6to4 tunnel between Cisco and Linux/Windows