A dir /all will tell you the exact file system. I have not seen 'slot' in a while, most now use disk (I believe it's dependent of the platform). ... View more

boot system flash disk0:/ Hope that helps. ... View more

Here's a link that should help- http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a00807fc191.shtml#Same ... View more

I don't think I've ever seen pps, but here might be a couple of helpful commands; 6503-1#show platform hardware capacity ? acl Show QoS/Security ACL capacity cpu Show CPU resources capacity eobc Show EOBC resources capacity fabric Show Switch Fabric resources capacity flash Show Flash/NVRAM resources capacity forwarding Show forwarding engine capacity ibc show IBC resources interface Show Interface resources capacity monitor Show SPAN resources capacity multicast Show L3 and LTL Multicast resources netflow Show Netflow capacity pfc Show PFC resources capacity power Show Power resources capacity qos Show QoS resources capacity rate-limit Show CPU Rate Limiters capacity system Show System resources capacity vlan Show VLAN resources capacity | Output modifiers 6503-1#show catalyst6000 ? all show all Catalyst 6000 information chassis-mac-addresses chassis MAC address range switching-clock switching-clock failure recovery mode traffic-meter current and peak traffic meter reading | Output modifiers 6503-1#show fabric ? active crossbar fabric linecard active and backup info channel-counters fabric channel counters clear-block clear-block congestion control for fabric channels drop drop counters for different queues in fabric errors fabric port errors status status of crossbar fabric switching-mode crossbar fabric and system switching modes utilization fabric port utilization percentage | Output modifiers ... View more

I don't think so. I think it's easier to deploy the other SW solution, NCM. I would rather manage one piece of software than 300 cron jobs. http://www.solarwinds.com/products/orion/configuration_manager/ ... View more

Most security conscience firms do have a long list of ACE on the inside interface. Another option is to use a proxy server. It's easier to filter on content than by ever changing IP's. If th list is small you could use regex. http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a0080940e04.shtml Hope that helps. ... View more

Chris- If you configure ISAKMP keepalives, it helps prevent sporadically dropped LAN-to-LAN or Remote Access VPN, which includes VPN clients, tunnels and the tunnels that are dropped after a period of inactivity. This feature lets the tunnel endpoint monitor the continued presence of a remote peer and report its own presence to that peer. If the peer becomes unresponsive, the endpoint removes the connection. In order for ISAKMP keepalives to work, both VPN endpoints must support them. *Cisco PIX/ASA 7.x and later, for the tunnel group named 10.165.205.222 securityappliance(config)#tunnel-group 10.165.205.222 ipsec-attributes securityappliance(config-tunnel-ipsec)#isakmp keepalive threshold 15 retry 10 http://www.cisco.com/en/US/products/ps6120/products_tech_note09186a00807e0aca.shtml Hope that helps. ... View more

What about creating a static ARP entry in the ASA. Will that work for you? ... View more

If there is no AAA group assigned, it will not use a password to enter user mode, it will just let you in. To enter privilege mode, you will have to enter the enable password. It's a good practice to configure AAA and use local authentication as a minimum. That way console connections must enter a username and password to gain access. ... View more

Like Joseph stated, if this goes over the internet, it's best effort. That being said, I have a client that was having this issue and as a test we gave priority to the remote end IP. It has resolved most of their VoIP issues over the VPN. class-map match-all VPN-CLASS match access-group name VPN policy-map QOS-POLICY class VPN-CLASS priority 512 class class-default fair-queue ip access-list extended VPN permit ip host 68.115.x.y any permit ip any host 68.115.x.y interface s0/0/0 service-policy output VPN-POLICY Hope that helps. ... View more

This might help. http://www.cisco.com/en/US/docs/security/asa/asa72/command/reference/s8_72.html#wp1198640 ... View more

The queries are going the other way. They are sourcing from your internal clients (10.1.1.1 and 10.1.17.6). This is typical if these are your DNS forwarders or they are configured to use the root hints. You might want to increase the message length for DNS, 512 tends to be a little too small. Hope that helps. ... View more