About urbinir

urbinir · 04-19-2024

Hi, we have a Cisco ACI in our LAB enviroment with an older version 2.2. We'd like reset/clean all the fabric (n.3 APIC,n.2 Leaf and n.2 Spine) and restart with a new version, the 5.2. Our hardware support it We don't need the backup of actual config...

urbinir · 05-19-2016

Hi I'm working with a Cisco 819 4G/LTE (model C819HG-4G-G-K9) with modem Sierra MC7710 When the router attached to the UMTS mobile radio network I saw that the speed is 384000bit/s as showed below: Cisco-819#sh run | beg line 3 line 3 script dialer...

urbinir · 02-10-2013

HelloI need an EEM applet that every 60 sec execute a show command and then write the output of the command on the flash memory of the router The output of the file might be not override because I need all the output of the show captured every 60 se...

urbinir · 09-29-2012

Hi,in the Cisco 7600 we have the following command to configure a service instance:service instance id ethernet [service-name]Searching information for the meaning of the service-name option I didn't find nothing..Do you know what service-name do an...

urbinir · 04-19-2012

Hi allI'm working on OAM Ethernet link-monitor Event but I don't understand the meaning of the Error symbol.I know that these error are layer 1 errors when the coding 64B/66B (10GE interface) is wrong but what is the real matching of one symbol?It's ...

urbinir · 04-19-2024

Hi Robert thank you for the answer Our switch support 5.2(2) we check here https://www.cisco.com/c/dam/en/us/td/docs/Website/datacenter/acihwsupport/index.html Our CIMC firmware is old , version 2.0(9c) But it seems is supported. Our idea is anyway ...

urbinir · 12-13-2016

Hi, same issue using ASR1001-X with asr1001x-universalk9.03.16.00.S.155-3.S-ext.SPA.bin Solved after inserting/removing a 10G SFP tranceiver into the TenGiga port All of those messages above disappeared and never happen again *Jan 12 06:08:08.622: ...

urbinir · 05-19-2016

Hi mchance, I'm not sure of that because if I switch on GSM/EDGE mobile network that output showed the tx and rx speed in different and separate values..instead when attached to UMTS network the output showed a value only as explained above Cisco-8...

urbinir · 02-11-2013

Hi Josephthx againSorry I don't understand how to add the append logic to my applet converted in TCL Using converter I have converted my applet with redirect flash:xxx (without .$_event_pub_sec) this is the result::cisco::eem::event_register_timer ...

urbinir · 02-11-2013

Hi Joseph,thx for your quickly reply..The EEM version is 3.20 and append is not supported on the file system3400_GIGETTO#sh event manager version Embedded Event Manager Version 3.20Component Versions:3400_GIGETTO#sh vers | append flash:% Appending is...

Member Since	‎07-01-2002 05:45 AM
Date Last Visited	‎04-24-2024 12:05 AM
Posts	29
Total Helpful Votes Received	5

User Statistics

User Activity

Rebuild Cisco ACI with a new version

Cisco 819 speed values

EEM redirect without overwrite the file

service-name meaning in the service instance command

OAM Ethernet 802.3ah: Error Symbol meaning

Re: Rebuild Cisco ACI with a new version

Hi, same issue using ASR1001

Hi mchance,

EEM redirect without overwrite the file

EEM redirect without overwrite the file