About kc-ussugar

kc-ussugar · 08-08-2009

Hello All,On 3 PRIs (MGCP gateway) I have every inbound PSTN call directed to a SIP trunk pointing to a 3rd-party IVR server. That works great.What I want to do is set up a failover scheme by which - in the event the IVR server fails - the same inbo...

kc-ussugar · 02-19-2009

Is it possible to change an existing CUE 3.2.2 integrated with CME, over to CUE 3.2.2 with CUCM 6.1.3a WITHOUT losing greetings, etc.?The only "integration guide" that seems to be authoritative is (Document ID: 60002), which states: "Note: There is n...

kc-ussugar · 01-15-2009

dbWalker in prep for upgrade from 4.0.5 to 5.0.1 gets following message:1694:(error) The '@PrimaryServer' property could not be found in the 'UnitySetupParameters' table. This can cause problems if you try to upgrade this system to a newer version of...

kc-ussugar · 09-06-2007

Current: Unity UM (Exchange) 4.2.1 on MCS 7825; no failover; no voice cards; integrated with CCM 4.2.3Target: Unity UM (Exchange) 4.2.1 on MCS 7835; WITH failover; no voice cards; integrated with CCM 4.2.3No messages stored on Unity before or after...

kc-ussugar · 08-26-2007

CCM 4.2.3 - Just replaced Publisher to better hardware; all went smooth, except cannot login. RTMT says "directory connection failed". All is well on the Subscriber; can login, etc. MUST I run the AD integration plugin after a BARS restore? Or is...

kc-ussugar · 10-21-2009

I've seen this scenario resolved by forcing the config from the VG side - OUT of config do the following:ccm-manager config-download check reset

kc-ussugar · 10-01-2009

Here's a Postscript, in case it's helpful to anyone - - TAC came up with a clever twist on j.schulenberg's idea - let the VG use BOTH H.323 and MGCP. So, in CUCM we added the gateway as H.323 and listed it in the RL as a separate RG beneath the SIP...

kc-ussugar · 09-19-2009

Thanks. And how I wish we could go that route. It would have fixed earlier issues with the 3rd-party IVR software's non 2.0 compliance, such as ignoring REFRESH and UPDATE (which they fixed with their new release of this month).Although CUBE would ...

kc-ussugar · 09-19-2009

The trunk is not to a Service Provider. It's a 3rd-party IVR box in the same room connected to the same switch. We just want to detect a call connect failure in the IVR system and ring hard phones when that happens. The reason we're going thru H32...

kc-ussugar · 09-19-2009

I have the same question. My route list contains a SIP trunk first, and then an H323 gateway. I can pull the ethernet cables out of the server on the other end of the SIP trunk, and Call Manager (7.0.2) still tries to send calls out the SIP trunk. ...

Member Since	‎09-28-2006 09:35 AM
Date Last Visited	‎08-18-2017 03:53 AM
Posts	41
Total Helpful Votes Received	19

User Statistics

User Activity

CUCM 7.0.2 design question - PRI-->SIP Trunk failover to PRI-->Hunt List

CUE-CME upgrade to CUE-CUCM

dbWalker - @PrimaryServer property not found in UnitySetupParameters

Unity upgrade question

AD intregration after BARS restore

Re: MGCP FXO Port registration Rejected

Re: CUCM 7.0.2 design question - PRI-->SIP Trunk failover to PRI

Re: How does CUCM detect SIP trunk failure

Re: How does CUCM detect SIP trunk failure

Re: How does CUCM detect SIP trunk failure